rewa
Member

3317 Likes

Page 48 of 222 First ... 343536373839404142434445464748495051525354555657585960616298148 ... Last

• Jump to page:

1. 
   rewa liked post by SixtyTen On thread : How to bend 40mm copper pipe 180° ?

   I bent some 25mm steel tube for a motorbike into a tight U bend a number of years back. I flattened and folded over one end, packed the tube as full as possible with sand (like compress it in there...

   Liked On: 17-08-2022, 01:58 PM

2. 
   rewa liked post by Maca49 On thread : How to bend 40mm copper pipe 180° ?

   My dad made a 1/2” copper coil about 4 foot long to fit in an 8” flue to heat water using the sand. He was one clever bugger. Fitted to a small chip heater, fired with waste oil. Emery thing glowed...

   Liked On: 17-08-2022, 01:57 PM

3. 
   rewa liked post by Maca49 On thread : How to bend 40mm copper pipe 180° ?

   Make sure the sand is DRY:)

   Liked On: 17-08-2022, 01:57 PM

4. 
   rewa liked post by XR500 On thread : How to bend 40mm copper pipe 180° ?

   All wetback units I have seen have been bits of straight pipe with the corners done using two 90degree elbows, all silfos'd together. As long as the copper pipe is always full of water the silfos...

   Liked On: 17-08-2022, 01:56 PM

5. 
   rewa liked post by 2post On thread : How to bend 40mm copper pipe 180° ?

   Copper tig welds really well, but welding with silfoss will be fine. If you get it hot enough in use to melt silfoss you’ll have other problems to worry about.

   Liked On: 17-08-2022, 01:56 PM

6. 
   rewa liked post by Maca49 On thread : How to bend 40mm copper pipe 180° ?

   You can fill it with sand and heat and bend, or use a plumbers spring if yo can find one of that diameter

   Liked On: 17-08-2022, 01:56 PM

7. 
   rewa liked post by Friwi On thread : Identify this action and barrel?

   If you don’t like the action, I ll buy it of you before it get molested :-)

   Liked On: 17-08-2022, 01:50 PM

8. 
   rewa liked post by PaulNZ On thread : Wood Stock Sealant

   Looks good. I'd stick with the BLO too. If it was end grain then it might be worth sealing more thoroughly, but otherwise you might as well match the exterior for water resistance. Idle musing...

   Liked On: 17-08-2022, 01:47 PM

9. 
   rewa liked post by Barry the hunter On thread : Wood Stock Sealant

   Boiled linseed will be fine - mix a tiny amount of turps with first coat-linseed will soak in better - suggest light sand first to remove any dirt etc

   Liked On: 17-08-2022, 01:46 PM

10. 
    rewa liked post by jakewire On thread : Wood Stock Sealant

    Current finish is Boiled linseed oil.:( It's what I had.) Top Rifle 203751

    Liked On: 17-08-2022, 01:46 PM

11. 
    rewa liked post by jakewire On thread : Walnut stock build (done the traditional way)

    Both those stocks look so bloody great.

    Liked On: 17-08-2022, 01:22 PM

12. 
    rewa liked post by Micky Duck On thread : Walnut stock build (done the traditional way)

    Van Gruff...you posted while I was typing...and what posted goes for you too........WOW.

    Liked On: 17-08-2022, 01:21 PM

13. 
    rewa liked post by Micky Duck On thread : Walnut stock build (done the traditional way)

    WOW...... that is gorgeous....hard to say it any other way,you are a talented man ,that rifle is a thing of beauty and will be family heirloom for generations to enjoy....... many years from now a...

    Liked On: 17-08-2022, 01:21 PM

14. 
    rewa liked post by Von Gruff Knives On thread : Walnut stock build (done the traditional way)

    I like cant as well as cast when building my own stocks https://i.imgur.com/NG5wwknl.jpg This was a superb blank I bought in from the US and with so much burl and grain changes was done primarily...

    Liked On: 17-08-2022, 01:20 PM

15. 
    rewa liked post by Hunter_Nick On thread : Walnut stock build (done the traditional way)

    And so after 89 1/4 hours of planing, chiselling, scraping, sanding and much thinking and looking, here is what I have. This is after the first ‘base coat’ of oil, which now needs to dry a couple of...

    Liked On: 17-08-2022, 01:20 PM

Page 48 of 222 First ... 343536373839404142434445464748495051525354555657585960616298148 ... Last

• Jump to page: