ROKTOY
Member

3239 Likes

Page 22 of 216 First ... 8910111213141516171819202122232425262728293031323334353672122 ... Last

• Jump to page:

1. 
   ROKTOY liked post by Joe Schmo On thread : Mid winter catch up

   Here…@ROKTOY Same thing just with you and stingray 252735

   Liked On: 15-06-2024, 02:23 PM

2. 
   ROKTOY liked post by Joe Schmo On thread : Mid winter catch up

   I know I sound like a hunting pack salesman but I could really care less. Either way, I’m not sure y’all know how badass the Kifaru brand packs are so for demonstration purposes, I’ll bring one and...

   Liked On: 12-06-2024, 09:16 PM

3. 
   ROKTOY liked post by XR500 On thread : Nice NZ hunting film

   Its a crying shame he only has 5.9K subscribers to his channel. His videography and content vie with channels one hundred times that size. Tell your mates to subscribe, even if its only to teach them...

   Liked On: 10-06-2024, 10:16 PM

4. 
   ROKTOY liked post by Micky Duck On thread : Socks

   sometimes slight difference in where padding is..sometimes not..the blond has TGIF on her socks...so she remembers toes go in first.

   Liked On: 09-06-2024, 03:29 PM

5. 
   ROKTOY liked post by Ground Control On thread : Photos of your dog

   My two favourite things at the moment ( after my wife and kids of course) 252148

   Liked On: 09-06-2024, 03:03 PM

6. 
   ROKTOY liked post by veitnamcam On thread : Fishing tomorrow!

   Out to check the carrot patch today with stingray. Conditions were fantastic no wind at all and a wee lazy swell. I had considered chucking the 223 in for some pest control but didn't and what do...

   Liked On: 08-06-2024, 08:45 PM

7. 
   ROKTOY liked post by Wurzelmangler On thread : Knifemaking photo-essay (5) Milling an internal angle in the guard

   1) I take multiple light cuts. 2) With the angle cut, note the cross slide reading (22 on the dial). Back off the cross slide, turn the blade over in the clamp, and angle the other side of the...

   Liked On: 06-06-2024, 11:22 PM

8. 
   ROKTOY liked post by Wurzelmangler On thread : Knifemaking photo-essay (6) Fitting the handle slabs

   The parts are nearly ready to be glued together. I wash the knife blank with hot soapy water, rinse it with hot water, and dry it with a towel. I also ensure my hands are clean. I dry-sand both...

   Liked On: 06-06-2024, 11:21 PM

9. 
   ROKTOY liked post by Joe Schmo On thread : This pisses me off!

   I do love how they show a couple of 500" stags to introduce regular old NZ huntin :) Almost related, I just watched a nz hunting show for the first time and found out that it's just like good ol'...

   Liked On: 06-06-2024, 08:11 PM

10. 
    ROKTOY liked post by Pengy On thread : The Old Knife.

    It aint pretty, but it does the job . A bit like the man himself I guess

    Liked On: 06-06-2024, 11:36 AM

11. 
    ROKTOY liked post by Barrel On thread : A singleshot.22 to fit the boy

    Recently found this post when searching for advice and was inspired by Roktoy's ingenuity. A couple of years ago I was given an old Slazenger/Lithgow singleshot .22 that I have tidied up over the...

    Liked On: 02-06-2024, 09:25 PM

12. 
    ROKTOY liked post by Fee Knicks On thread : A singleshot.22 to fit the boy

    Dont have any parts but do suggest that you slim that wrist area a lot more to suit small hands . Being able to reach the trigger whilst wrapping the thumb around the wrist makes it much easier to...

    Liked On: 02-06-2024, 09:25 PM

13. 
    ROKTOY liked post by 6x47 On thread : A singleshot.22 to fit the boy

    Pretty much snap on that. About two years ago, I was given a Slazenger SS in rather rough condition but did a tidy up on it. My grandson is just five but is pretty damn tall so I fancy I can let him...

    Liked On: 02-06-2024, 09:25 PM

14. 
    ROKTOY liked post by Shearer On thread : Hand held thermal now legal on public land

    The arguments against thermals is a bit like when optical sights (scopes) first appeared. Some thought it made it too easy but I guess everyone has got over that now. Just because you are seeing more...

    Liked On: 01-06-2024, 11:48 AM

15. 
    ROKTOY liked post by robhughes-games On thread : HGPRECISION. Cnc gunsmithing and services

    Hi all. I've recently quit my job as a full time machinist to start up my own business. Bad time to start up but here it goes. I think a lot of the products we import for firearms could be made...

    Liked On: 30-05-2024, 12:20 AM

Page 22 of 216 First ... 8910111213141516171819202122232425262728293031323334353672122 ... Last

• Jump to page: