Ross Nolan
Member

2324 Likes

Page 38 of 155 First ... 242526272829303132333435363738394041424344454647484950515288138 ... Last

• Jump to page:

1. 
   Husky1600#2 liked post by Ross Nolan On thread : Looking for a good all around rifle

   For a beginners point and squirt rifle I think that you need something between 6 and 8mm, firing a bullet of between 90 and 165 grains, between 2600 and 3100 fps. Then you need to go and shoot it...

   Liked On: 09-07-2024, 12:50 PM

2. 
   Hunty1 liked post by Ross Nolan On thread : Show me your knives

   254279 Made this out of O1 hardened to Rc59 to test the shape - if it's good I'll make a better version out of 14C28. If not, I'll keep regrinding away at it till I'm happy.

   Liked On: 08-07-2024, 10:53 PM

3. 
   erniec liked post by Ross Nolan On thread : Show me your knives

   254279 Made this out of O1 hardened to Rc59 to test the shape - if it's good I'll make a better version out of 14C28. If not, I'll keep regrinding away at it till I'm happy.

   Liked On: 08-07-2024, 08:47 PM

4. 
   Nick-D liked post by Ross Nolan On thread : Show me your knives

   254279 Made this out of O1 hardened to Rc59 to test the shape - if it's good I'll make a better version out of 14C28. If not, I'll keep regrinding away at it till I'm happy.

   Liked On: 07-07-2024, 08:39 PM

5. 
   Barefoot liked post by Ross Nolan On thread : Show me your knives

   254279 Made this out of O1 hardened to Rc59 to test the shape - if it's good I'll make a better version out of 14C28. If not, I'll keep regrinding away at it till I'm happy.

   Liked On: 07-07-2024, 06:11 PM

6. 
   Micky Duck liked post by Ross Nolan On thread : Show me your knives

   254279 Made this out of O1 hardened to Rc59 to test the shape - if it's good I'll make a better version out of 14C28. If not, I'll keep regrinding away at it till I'm happy.

   Liked On: 07-07-2024, 05:49 PM

7. 
   XR500 liked post by Ross Nolan On thread : Landcruiser Help/advice

   https://partsouq.com/en/catalog/genuine/pick?c=Toyota&model=LAND+CRUISER&ssd=%24%2AKwEudHMXLSgvAAAAAJTUXQ0%3D%24 These guys are pretty good, delivery typically less than a week.

   Liked On: 05-07-2024, 11:05 AM

8. 
   Pointer liked post by Ross Nolan On thread : Pheasant hunting

   Dash and I are ready. A couple of weeks ago. No pheasants were harmed in the making of this video. https://www.youtube.com/watch?v=3NCx98C55tY

   Liked On: 04-07-2024, 01:54 PM

9. 
   paremata liked post by Ross Nolan On thread : What breed should I do the deer dog blueprint with?

   Wow. I can't believe you make that poor dog lay on the floor. Heartless. Just heartless.253692

   Liked On: 03-07-2024, 10:00 PM

10. 
    erniec liked post by Ross Nolan On thread : Landcruiser Help/advice

    https://partsouq.com/en/catalog/genuine/pick?c=Toyota&model=LAND+CRUISER&ssd=%24%2AKwEudHMXLSgvAAAAAJTUXQ0%3D%24 These guys are pretty good, delivery typically less than a week.

    Liked On: 02-07-2024, 08:04 PM

11. 
    Beaker liked post by Ross Nolan On thread : advice on using solid Ali rivets

    Are the rivet heads domed? You may need a "set" to help form the new heads. Basically it is a Block of steel with the head shape machined into it, held against the shank when the hammering is done....

    Liked On: 02-07-2024, 05:17 PM

12. 
    Micky Duck liked post by Ross Nolan On thread : The lightening project

    I think that you should take a deep breath and get over yourself. I was pointing out that 3 years of C marks will get you a degree. As an engineer who also has an MBA, employing a BE (hons)...

    Liked On: 02-07-2024, 10:40 AM

13. 
    XR500 liked post by Ross Nolan On thread : advice on using solid Ali rivets

    Are the rivet heads domed? You may need a "set" to help form the new heads. Basically it is a Block of steel with the head shape machined into it, held against the shank when the hammering is done....

    Liked On: 02-07-2024, 09:49 AM

14. 
    Stocky liked post by Ross Nolan On thread : The lightening project

    "C"s get degrees.... And that is some very nice machine work.

    Liked On: 01-07-2024, 03:43 PM

15. 
    Gfootey liked post by Ross Nolan On thread : What breed should I do the deer dog blueprint with?

    Wow. I can't believe you make that poor dog lay on the floor. Heartless. Just heartless.253692

    Liked On: 30-06-2024, 01:44 PM

Page 38 of 155 First ... 242526272829303132333435363738394041424344454647484950515288138 ... Last

• Jump to page: