RugerM77
Member

435 Likes

Page 26 of 29 First ... 121314151617181920212223242526272829 Last

• Jump to page:

1. 
   RugerM77 liked post by shooternz On thread : Cartridge suggestions

   Take a look at the 7x64 / 280 Rem 30/06 like the .308 case based cartridges on steroids with out the recoil , My pick would be the 7x64 with Norma ammo if factory is what you will be shooting most.

   Liked On: 29-11-2021, 02:24 PM

2. 
   RugerM77 liked post by zimmer On thread : Playing with some Redding Competition Shell Holders

   Here's a chart to help understand Redding Competition Shell Holders and what effect they have. This is my set measured using a Mitutoyo depth micrometer so reasonably accurate. I measured at three...

   Liked On: 14-11-2021, 03:51 PM

3. 
   RugerM77 liked post by zimmer On thread : Trying something, Eric Cortina method of load development

   I have used all sorts of methods - split case necks and close on long seated bullet, Stoney Point (now Hornady OAL gauge) method, Sinclairs tool for measuring seating depth (lies in cupboard unused),...

   Liked On: 13-11-2021, 06:50 PM

4. 
   RugerM77 liked post by Puffin On thread : Trying something, Eric Cortina method of load development

   Just a note on the above, #69: threaded "modified" cases are for the OAL gauge, a measurement that M. Cortina is at pains to emphasize is not required for his method. The stock photo I posted is...

   Liked On: 13-11-2021, 08:45 AM

5. 
   RugerM77 liked post by dannyb On thread : Trying something, Eric Cortina method of load development

   You raise a valid point, I should be very clear I am no Olympic marksman this is true, but I can shoot and at 100 yards I'm confident in knowing if I have pulled a shot or not. Your also correct 3...

   Liked On: 10-11-2021, 12:18 PM

6. 
   RugerM77 liked post by grandpamac On thread : Taupo range

   Greetings All, Agree with the last few posts. Marksmanship is only developed through practice. I used to be a reasonable shot in our club competitions and even had my name engraved on a few...

   Liked On: 18-10-2021, 10:08 AM

7. 
   RugerM77 liked post by Micky Duck On thread : When men were men

   well it seems these fellas are a bit shy.... I will add short tale concerning a member on here.... we were away on hunting trip way down south.... the 3 of us had roared up 1 antlered stag,then...

   Liked On: 14-10-2021, 08:51 PM

8. 
   RugerM77 liked post by Blackfern On thread : Recipe for Howa 1500 .308

   Just to throw another idea in the mix. I'm using Sako factory 123 grn in my howa 308 and get 10mm c t c groups at 100mtrs.

   Liked On: 13-10-2021, 01:24 PM

9. 
   RugerM77 liked post by The bomb On thread : Recipe for Howa 1500 .308

   Sako A7 , 16 in barrel. 43g 2206h and any 150g pill except Barnes,all shoot under inch @ 100 m ,just slightly different point of impacts.

   Liked On: 13-10-2021, 10:07 AM

10. 
    RugerM77 liked post by dogmatix On thread : Recipe for Howa 1500 .308

    In my Howa Bravo .308 I'm shooting Hornady 155gn HPBT with 44.5gn of 2206h, Fed Match primers and Lapua brass. Also Hornady 168gn ELD-M with 42.5gn 2206H. Same primers and brass. Still playing...

    Liked On: 13-10-2021, 10:07 AM

11. 
    RugerM77 liked post by 257weatherby On thread : Recipe for Howa 1500 .308

    Currently at 45.5 2206h pushing a 165 Targex and 47gn 2206h pushing a 150 Speer Hotcor. I don't reckon you can get enough stick powder in the case to get into trouble. Ball powder and mag primers...

    Liked On: 13-10-2021, 10:06 AM

12. 
    RugerM77 liked post by Dama dama On thread : Recipe for Howa 1500 .308

    My main rifle is a howa 1500 in .308win for which I reload. I don't think there is any advice i would give that wouldn't apply to any other 308. 2206H is ideal, and probably the most versatile...

    Liked On: 11-10-2021, 04:24 PM

13. 
    RugerM77 liked post by grandpamac On thread : Taupo range

    This makes it a bit easier on the Taupo Range, 180642 Grandpamac.

    Liked On: 09-10-2021, 08:52 AM

14. 
    RugerM77 liked post by TARGEX On thread : NZDA rimfire competition target

    Cant help with the pdf but if you want official NZDA targets they are just down the road from you if you are Kerikeri area at the Oramahoe NZDA range. If you want contact details etc just contact...

    Liked On: 29-09-2021, 08:45 AM

15. 
    RugerM77 liked post by Danger Mouse On thread : chrony on factory loads

    Welcome to my ignore list

    Liked On: 19-08-2021, 02:20 PM

Page 26 of 29 First ... 121314151617181920212223242526272829 Last

• Jump to page: