RugerM77
Member

402 Likes

Page 7 of 27 First 123456789101112131415161718192021 ... Last

• Jump to page:

1. 
   RugerM77 liked post by mudgripz On thread : IMPORTANT ANNOUNCEMENT

   Dan - have never had an issue with your moderation. Not once. As Snap says above - no apology needed. You provide a very useful service - carry on with the good wishes of all. Cheers Mike

   Liked On: 30-05-2023, 02:57 PM

2. 
   RugerM77 liked post by dannyb On thread : IMPORTANT ANNOUNCEMENT

   it' ain't worth it bro....you only enjoy it as it takes the heat off you right :yaeh am not durnk:

   Liked On: 29-05-2023, 09:45 PM

3. 
   RugerM77 liked post by MB On thread : IMPORTANT ANNOUNCEMENT

   No idea what you're on about, but keep up the good work.

   Liked On: 29-05-2023, 09:44 PM

4. 
   RugerM77 liked post by Micky Duck On thread : IMPORTANT ANNOUNCEMENT

   ya calls a spade a spade...dont change mate. you doing a good job...and filling a void that needed filled,moderator response time is at all time low/quickness,which is a great thing when something...

   Liked On: 29-05-2023, 09:44 PM

5. 
   RugerM77 liked post by dannyb On thread : IMPORTANT ANNOUNCEMENT

   I would like to take the opportunity to formally extend an apology to the general forum community. I have at times been a little pointed and abrupt about issues that could have been dealt with a...

   Liked On: 29-05-2023, 03:49 PM

6. 
   RugerM77 liked post by johnd On thread : Using comparator tool when seating projectiles.

   I have another approach to this. It can also be done prior to sizing. Especially if you are just bumping the shoulder with a bushing die and mandrel. https://youtu.be/02xWd-vBtFM

   Liked On: 29-05-2023, 01:28 PM

7. 
   RugerM77 liked post by gqhoon On thread : Using comparator tool when seating projectiles.

   Have a look at the Short Action Customs bullet comparators….the insert matches the leade angle dimensions of your barrel / chamber. So BTO measurements you take relate to where the projectile...

   Liked On: 28-05-2023, 09:27 PM

8. 
   RugerM77 liked post by Kiwilad2021 On thread : Using comparator tool when seating projectiles.

   Speaking of graphite powder where is the best place to get some without costing a small fortune? Cheers

   Liked On: 28-05-2023, 03:12 PM

9. 
   RugerM77 liked post by 7mmsaum On thread : Using comparator tool when seating projectiles.

   Use cotton buds to wipe graphite powder on the inside of case necks and on projectiles Fingers stay clean then

   Liked On: 28-05-2023, 02:13 PM

10. 
    RugerM77 liked post by 7mmsaum On thread : Using comparator tool when seating projectiles.

    Zimmers method is perfect Seat 10 thou too long them measure with the comparator Write that number down if you need to Then adjust the micrometer seating stem down for the last amount ...

    Liked On: 28-05-2023, 01:04 PM

11. 
    RugerM77 liked post by Ranger 888 On thread : Minimum pack contents

    We used to run a series of 3 weekend courses, spread out over several months: Basic Bushcraft, which involved the "classroom" content, e.g. first aid, food and cooking, pack contents, tents and...

    Liked On: 26-05-2023, 03:12 PM

12. 
    RugerM77 liked post by yeah_na_missed On thread : Minimum pack contents

    Ha ha, I read Tahr and BarrytheHunter's posts fully aware I carry too much and feeling utterly ashamed, so instantly resolved to cull a lot of shit... but then read Ranger888's post - especially the...

    Liked On: 26-05-2023, 08:27 AM

13. 
    RugerM77 liked post by Barry the hunter On thread : Minimum pack contents

    yup and get a fire going

    Liked On: 25-05-2023, 09:23 PM

14. 
    RugerM77 liked post by Barry the hunter On thread : Minimum pack contents

    I was a Mountain Safety Instructor for over 30 years and would never have pulled that stunt on anyone - I would have told him to get fucked and walked back inside

    Liked On: 25-05-2023, 09:22 PM

15. 
    RugerM77 liked post by Black Rabbit On thread : Fires

    Hi@Barry the hunter I am no expert for metal works, only share my living experience, and I have those modern cookware but they are only designed for cook a hot meal. The cast iron ones is not...

    Liked On: 22-05-2023, 10:21 PM

Page 7 of 27 First 123456789101112131415161718192021 ... Last

• Jump to page: