shooternz
Member

983 Likes

Page 11 of 66 First 1234567891011121314151617181920212223242561 ... Last

• Jump to page:

1. 
   winaa liked post by shooternz On thread : Pistol powders in rifles question

   Ap70n is ADI's version of Unique it is sold in the US as Universal standard cast bullet start load is 10 grains in .30 cal rifles with a 180-200 grain bullet, should not need a filler if the...

   Liked On: 07-07-2022, 10:14 PM

2. 
   Bill999 liked post by shooternz On thread : 7mm08 or .243 Subsonic round

   You wil probably have stability problems with 150 gr bullets in the 7mmo8 the standard 1:9.5" and 1:9" twists mat not stabilise them the 120 grain is the best option, Same with the .243 use the...

   Liked On: 05-07-2022, 08:43 AM

3. 
   Micky Duck liked post by shooternz On thread : 7mm08 or .243 Subsonic round

   You wil probably have stability problems with 150 gr bullets in the 7mmo8 the standard 1:9.5" and 1:9" twists mat not stabilise them the 120 grain is the best option, Same with the .243 use the...

   Liked On: 04-07-2022, 07:52 PM

4. 
   Jhon liked post by shooternz On thread : Questions for you 30-30 Cast Bullet aficionados

   Hi John, good to see the 151 HP going that fast I have seen the damage they do at 1600 fps at 2300 they will be like bombs! The 151 is designed for the .308 chamber which is cut to fit 168 SMK's...

   Liked On: 29-06-2022, 09:12 PM

5. 
   Micky Duck liked post by shooternz On thread : Questions for you 30-30 Cast Bullet aficionados

   Hi John, good to see the 151 HP going that fast I have seen the damage they do at 1600 fps at 2300 they will be like bombs! The 151 is designed for the .308 chamber which is cut to fit 168 SMK's...

   Liked On: 29-06-2022, 07:41 PM

6. 
   257weatherby liked post by shooternz On thread : LEE LEAD MELTER ADVICE

   Don not melt scrap lead in the pot that you are going to cast bullets only use clean lead that has been melt down a had the shit fluid out of it, Buy 50/50 solder sticks for the tin I stick to a pot...

   Liked On: 15-06-2022, 12:33 PM

7. 
   winaa liked post by shooternz On thread : LEE LEAD MELTER ADVICE

   Start with 1 stick to 10 kg of lead is usually enough you only need enough to fill out the mould Tin is not for hardness, For hunting bullets the softer the better, High velocity with cast is...

   Liked On: 14-06-2022, 10:51 PM

8. 
   BSA liked post by shooternz On thread : LEE LEAD MELTER ADVICE

   Don not melt scrap lead in the pot that you are going to cast bullets only use clean lead that has been melt down a had the shit fluid out of it, Buy 50/50 solder sticks for the tin I stick to a pot...

   Liked On: 14-06-2022, 07:42 AM

9. 
   rupert liked post by shooternz On thread : Incremental load test anomalies

   It is the neck of the case there is only so much gas can flow through the neck of the case when the maximum flow rate is exceeded there is a bottle neck and the gas flow can't flow fast enough and...

   Liked On: 09-06-2022, 12:28 PM

10. 
    Micky Duck liked post by shooternz On thread : Incremental load test anomalies

    It is the neck of the case there is only so much gas can flow through the neck of the case when the maximum flow rate is exceeded there is a bottle neck and the gas flow can't flow fast enough and...

    Liked On: 07-06-2022, 07:56 PM

11. 
    winaa liked post by shooternz On thread : Magnum primers with Trailboss ?

    Don't worry about the primers you are working at the bottom of the load density range, In a .308 most use 8.0 grains of Trail Boss for about 1040 fps so you have plenty of spread left in the...

    Liked On: 07-06-2022, 11:10 AM

12. 
    Shearer liked post by shooternz On thread : Magnum primers with Trailboss ?

    Don't worry about the primers you are working at the bottom of the load density range, In a .308 most use 8.0 grains of Trail Boss for about 1040 fps so you have plenty of spread left in the...

    Liked On: 07-06-2022, 11:06 AM

13. 
    Pete_D liked post by shooternz On thread : Magnum primers with Trailboss ?

    Don't worry about the primers you are working at the bottom of the load density range, In a .308 most use 8.0 grains of Trail Boss for about 1040 fps so you have plenty of spread left in the...

    Liked On: 07-06-2022, 10:16 AM

14. 
    Moa Hunter liked post by shooternz On thread : Incremental load test anomalies

    It is the neck of the case there is only so much gas can flow through the neck of the case when the maximum flow rate is exceeded there is a bottle neck and the gas flow can't flow fast enough and...

    Liked On: 06-06-2022, 11:29 PM

15. 
    Micky Duck liked post by shooternz On thread : Magnum primers with Trailboss ?

    Don't worry about the primers you are working at the bottom of the load density range, In a .308 most use 8.0 grains of Trail Boss for about 1040 fps so you have plenty of spread left in the...

    Liked On: 06-06-2022, 10:23 PM

Page 11 of 66 First 1234567891011121314151617181920212223242561 ... Last

• Jump to page: