shooternz
Member

904 Likes

Page 1 of 61 12345678910111213141551 ... Last

• Jump to page:

1. 
   shooternz liked post by The bomb On thread : 308 bush pig loads

   150g corlokts 43g 2206h,110g Barnes 45g 2206h as lighter option with less recoil for my boy..both kill well at bush ranges.

   Liked On: 22-02-2024, 01:01 PM

2. 
   shooternz liked post by zimmer On thread : Making case lube

   Just follow Mickies advise - Imperial Sizing Wax No stuck cases A small tin lasts centuries. Use the lanolin on your trailer chassis.

   Liked On: 09-09-2023, 06:59 PM

3. 
   shooternz liked post by Micky Duck On thread : Making case lube

   Ive got and use.. frog lube...awesome smells like camphor vasoline...cheap and just works imperial sizing wax...enough said powdered graphite..reat for doing necks..but the sizing wax sort of...

   Liked On: 09-09-2023, 06:58 PM

4. 
   shooternz liked post by tetawa On thread : 228 Speer projectiles in 223.

   These aren't the blunt nosed projectile, they are pointed spire point with the cannulure, their actually 227 diameter.

   Liked On: 05-09-2023, 11:51 AM

5. 
   shooternz liked post by grandpamac On thread : Reload 308 using magnum LRP 2208 powder vs standard LRP 2206H

   Greetings, AR2208 is easy to ignite, especially with LRP in a .308 case. Magnum primers give no advantage and possibly less than that. My go to powder in the .308 is AR2206H and has been for some...

   Liked On: 22-08-2023, 01:12 PM

6. 
   shooternz liked post by 57jl On thread : Reload 308 using magnum LRP 2208 powder vs standard LRP 2206H

   no

   Liked On: 22-08-2023, 01:11 PM

7. 
   shooternz liked post by akaroa1 On thread : Seating die marking projectiles

   Disassemble again and smooth out the inside corner on the steating stem where it contacts the projectile Spin it in a drill and use fine sand paper and then 0000 steel wool on the offending mark...

   Liked On: 28-07-2023, 02:55 PM

8. 
   shooternz liked post by Jhon On thread : Primers from Ozz

   Call the airline and ask maybe?

   Liked On: 27-07-2023, 09:34 AM

9. 
   shooternz liked post by JohnDuxbury On thread : my 7x60 wildcat project

   Ummm, why didnt you just make it a 7x64mm? Very common in Europe. Am I being too obvious?

   Liked On: 23-07-2023, 12:25 AM

10. 
    shooternz liked post by Micky Duck On thread : Some Thoughts on Handloading.

    the hard rules still apply #1 try to find data from at least 3 different places preferably one being a real paper manual #2 if unknown rifle..start low and slowly/carefully work up #3 double...

    Liked On: 23-07-2023, 12:02 AM

11. 
    shooternz liked post by TeRei On thread : Subsonic .223rem

    When you are talking about still effective killing you would need at least 7gr's otherwise it would dribble out of the barrel. My mate has 9 baffles on his DPT can. It is very quiet.

    Liked On: 05-06-2023, 08:18 PM

12. 
    shooternz liked post by Shearer On thread : Subsonic .223rem

    I am only planning on using them on rabbits, possums etc. I had best explain better. At the moment I am doing a bit of pest control on local properties. Mostly rabbits etc but do come across the...

    Liked On: 05-06-2023, 11:45 AM

13. 
    shooternz liked post by Jhon On thread : 30 30 reloads

    30-30 loves IMR 3031 - if you can find it. There is current load data on Hogdon site online

    Liked On: 25-05-2023, 10:48 AM

14. 
    shooternz liked post by Marty Henry On thread : 30 30 reloads

    If the speers Don't have a cannelure to crimp into you will have to single load for a lever gun. For that application I'd use cast bullets like robs 150 gr with 8 to10 grains of a pistol powder. It...

    Liked On: 25-05-2023, 10:48 AM

15. 
    shooternz liked post by Mathias On thread : Magnum primers in a 260?

    Yes you should reduce your charge for magnum primers in the first instance. How much, well I'd go back at least 1.5gr and go from there to be safe. You might well end up with the same load but with a...

    Liked On: 15-05-2023, 09:18 PM

Page 1 of 61 12345678910111213141551 ... Last

• Jump to page: