shooternz
Member

911 Likes

Page 2 of 61 First 1234567891011121314151652 ... Last

• Jump to page:

1. 
   shooternz liked post by JohnDuxbury On thread : my 7x60 wildcat project

   Ummm, why didnt you just make it a 7x64mm? Very common in Europe. Am I being too obvious?

   Liked On: 23-07-2023, 12:25 AM

2. 
   shooternz liked post by Micky Duck On thread : Some Thoughts on Handloading.

   the hard rules still apply #1 try to find data from at least 3 different places preferably one being a real paper manual #2 if unknown rifle..start low and slowly/carefully work up #3 double...

   Liked On: 23-07-2023, 12:02 AM

3. 
   shooternz liked post by TeRei On thread : Subsonic .223rem

   When you are talking about still effective killing you would need at least 7gr's otherwise it would dribble out of the barrel. My mate has 9 baffles on his DPT can. It is very quiet.

   Liked On: 05-06-2023, 08:18 PM

4. 
   shooternz liked post by Shearer On thread : Subsonic .223rem

   I am only planning on using them on rabbits, possums etc. I had best explain better. At the moment I am doing a bit of pest control on local properties. Mostly rabbits etc but do come across the...

   Liked On: 05-06-2023, 11:45 AM

5. 
   shooternz liked post by Jhon On thread : 30 30 reloads

   30-30 loves IMR 3031 - if you can find it. There is current load data on Hogdon site online

   Liked On: 25-05-2023, 10:48 AM

6. 
   shooternz liked post by Marty Henry On thread : 30 30 reloads

   If the speers Don't have a cannelure to crimp into you will have to single load for a lever gun. For that application I'd use cast bullets like robs 150 gr with 8 to10 grains of a pistol powder. It...

   Liked On: 25-05-2023, 10:48 AM

7. 
   shooternz liked post by Mathias On thread : Magnum primers in a 260?

   Yes you should reduce your charge for magnum primers in the first instance. How much, well I'd go back at least 1.5gr and go from there to be safe. You might well end up with the same load but with a...

   Liked On: 15-05-2023, 09:18 PM

8. 
   shooternz liked post by Marty Henry On thread : 30-40 Krag load conundrums

   An old book tells me imr 4064 (ar2208) will do it all from 110 to 220 grains and the oldest adi book reckons 2206h. For 165s 37-42 gr 2208, 33-38 2206h is what I can find

   Liked On: 08-05-2023, 06:43 PM

9. 
   shooternz liked post by SmokeyJason On thread : Speer 30 grain TNT Green .224

   Ah if only. As I could use it in the 22 hornet.

   Liked On: 07-05-2023, 01:13 PM

10. 
    shooternz liked post by ChrisW On thread : 308 - short barrel loads for medium-long range

    The powder that gives the highest velocity in a long barrel will also give the highest velocity in a short barrel, so powder choice is the same as what you'd usually pick.

    Liked On: 28-04-2023, 07:15 PM

11. 
    shooternz liked post by XR500 On thread : No more powder

    ...Which aggressor? There's more than one.

    Liked On: 25-04-2023, 02:48 PM

12. 
    shooternz liked post by grandpamac On thread : Recommended Reloading Reading

    Greetings, Handloader Ammunition Reloading Journal put out by Wolf Publishing and Load Data dot com are good sources for reliable articles and data, together with the Hodgdons and ADI on line load...

    Liked On: 22-04-2023, 01:37 PM

13. 
    shooternz liked post by Friwi On thread : What 22-250 in a 1-8 twist.

    To go Semi factory 1in 8 twist, you have to buy two tikkas. 1 varmint one in 223 1 in 8 twist that you rechamber and use the bolt of a standard 22-250/ 308 bolt face. But then you end up with a...

    Liked On: 07-04-2023, 05:39 PM

14. 
    shooternz liked post by Morepork On thread : 303 wildcats??

    I have one, I made a few years ago, 35/303 I used a 35 Whelen reamer, it was reamed into the 303 case length, all work was done at True Flite, fitted red and green fibre optic open sights. I cut...

    Liked On: 06-03-2023, 10:20 AM

15. 
    shooternz liked post by Dermastor On thread : Moly for barrel?

    I don't believe it will work that well. I had a 7mm Rem Mag that copper fouled like crazy. I tried all sorts of moly barrel treatments and projectile coatings to no avail. It was very accurate, but...

    Liked On: 03-03-2023, 11:34 AM

Page 2 of 61 First 1234567891011121314151652 ... Last

• Jump to page: