shooternz
Member

911 Likes

Page 4 of 61 First 12345678910111213141516171854 ... Last

• Jump to page:

1. 
   shooternz liked post by TeRei On thread : Case Lube Alternatives?

   My mate who is a farmer looks out of his kitchen window to his shearing shed and gets his sizing wax off a white thing.Some high tech stuff called nano-lanolin. His father and grandfather did the...

   Liked On: 19-10-2022, 08:55 PM

2. 
   shooternz liked post by Tommy On thread : Case Lube Alternatives?

   Lanolin in isopropyl alcohol is basically dillon size lube. Depends what you're doing though. The aforementioned sizing wax is boss

   Liked On: 19-10-2022, 08:48 PM

3. 
   shooternz liked post by southernman On thread : 9.3x62 loads

   Just cause this thread need pictures. 208185208186 couple of the 9.3x74 double rifle. Sako Bavarian 20" 208187

   Liked On: 16-10-2022, 09:46 AM

4. 
   shooternz liked post by imaca On thread : Swiss rifle range across a road

   Just goes to show what rational thought and a lack of hysteria can achieve

   Liked On: 08-10-2022, 07:12 PM

5. 
   shooternz liked post by Marty Henry On thread : 8x57 projectiles

   Your s&b 196 grainers won't dissapoint.

   Liked On: 07-10-2022, 12:16 AM

6. 
   shooternz liked post by Friwi On thread : Rem700 adl front trigger sceew

   Just a light tension with a bit of blue loctite and that is how do all of mines. Less chance of creating stress in the bedding and the action.

   Liked On: 04-10-2022, 09:43 AM

7. 
   shooternz liked post by 7mmsaum On thread : Cast bullet bc’s

   Zero at 100 Shoot at 400 target Measure drop in inches or moa Use ballistic calculator and keep adding bc value until calculator shows actual measured drop That will get you close

   Liked On: 03-10-2022, 06:38 PM

8. 
   shooternz liked post by Jhon On thread : Loading IMR 4895 in 308

   I'm interested in this one brass approach as it is commonly stated. Genuine question here - How much does it really matter for hunting, especially for meat for the table? Why I ask: 1....

   Liked On: 27-09-2022, 12:36 PM

9. 
   shooternz liked post by Marty Henry On thread : Removing 'leading' from shooting cast bullets

   1/ lube your bullets 2/lube your bullets 3/ dOnt push them too fast, over 1400 fps gas checks do help a bit. 4/ alead is soft, bronze brush will remove leading use kerosene as a lube for the...

   Liked On: 26-09-2022, 09:34 AM

10. 
    shooternz liked post by Fireflite On thread : Quick release rings, are they worth it?

    I've run several sets of Warne QD rings. Sitting on 223 to 9.3x62 and never had any issues. Hunt around for a good price!

    Liked On: 22-09-2022, 10:33 AM

11. 
    shooternz liked post by Hurricane On thread : Case Trimmers..

    LE Wilson for me too. The case holder ensures concentric cuts every time, which many of the others cannot replicate. Does that make a difference? Maybe yes, maybe no, but if we are about limiting...

    Liked On: 19-09-2022, 09:40 AM

12. 
    shooternz liked post by akaroa1 On thread : Cast Lead Thread ?

    Saeco #311 mould arrived so I just had to cast a few Very nice mould And once up to heat it turns out a very nice bullet with care Not so much a bore rider but a tapered shoulder Truncated cone...

    Liked On: 16-09-2022, 10:22 PM

13. 
    shooternz liked post by Cyclops On thread : Seating depth tolerances

    Unlikely unless you have a particularly fussy rifle. My rifles aren't very fussy. One had more than 6500 rounds fired, another more than 5500, without adjusting seating depth. As the throat...

    Liked On: 10-09-2022, 12:48 AM

14. 
    shooternz liked post by silentscope On thread : 300 Win mag projectiles

    I like the 178 eld-x. I found it a good balance of long range hitting power and flat shooting out of my rifle.

    Liked On: 10-09-2022, 12:44 AM

15. 
    shooternz liked post by Makros On thread : Lee aniversary kit

    I started with one, I have upgraded everything. I found the Lee press was too flexible and lead to under sizing and really struggling on some calibres (7.5x55 was the worst for some reason) and lead...

    Liked On: 31-08-2022, 01:59 PM

Page 4 of 61 First 12345678910111213141516171854 ... Last

• Jump to page: