shooternz
Member

983 Likes

Page 9 of 66 First 123456789101112131415161718192021222359 ... Last

• Jump to page:

1. 
   Nasty Factory Trigger liked post by shooternz On thread : Subsonic load for 308

   Seat to the crimp groove the bullet is designed to be seated so the base is flush with the base of the neck in a .308 give it a light crimp and you are set

   Liked On: 12-08-2022, 08:41 PM

2. 
   Bill999 liked post by shooternz On thread : Roll crimping 308 subs

   Your are spot on, with jacketed bullets the only cases that may need a crimp are the ones with short necks and very heavy recoil then it would be prudent to use bullets with a cannelure and crimp...

   Liked On: 11-08-2022, 08:44 AM

3. 
   grandpamac liked post by shooternz On thread : Roll crimping 308 subs

   Your are spot on, with jacketed bullets the only cases that may need a crimp are the ones with short necks and very heavy recoil then it would be prudent to use bullets with a cannelure and crimp...

   Liked On: 10-08-2022, 07:38 PM

4. 
   Moa Hunter liked post by shooternz On thread : necking up 243 to 7mm08

   I have necked up a couple of hundred .243 win cases to 7mm08 without any drama Remington Winchester Horandy all with one pass through a Redding FL die it does have a nice tapered expander button...

   Liked On: 04-08-2022, 08:27 PM

5. 
   Bill999 liked post by shooternz On thread : necking up 243 to 7mm08

   I have necked up a couple of hundred .243 win cases to 7mm08 without any drama Remington Winchester Horandy all with one pass through a Redding FL die it does have a nice tapered expander button...

   Liked On: 03-08-2022, 08:41 AM

6. 
   40mm liked post by shooternz On thread : Bolt face Diameters - Cheat Sheet

   The cheat sheet needs updating every month at the rate new and totally unnecessary cartridges are hitting the market place manufacturers can't supply components for the common calibres already in...

   Liked On: 31-07-2022, 07:42 PM

7. 
   veitnamcam liked post by shooternz On thread : Any ideas? Cratered primers and looks as though the strike is all over the primer

   Getting the firing pin bushed will sort that out any decent Gunsmith can do it.

   Liked On: 31-07-2022, 07:22 PM

8. 
   Micky Duck liked post by shooternz On thread : Questions for you 30-30 Cast Bullet aficionados

   Would you like a hundred 7mm 133 HP as well a customer swapped them for 151 HP's he traded hie 7mm for a .308

   Liked On: 31-07-2022, 01:56 PM

9. 
   Tikka7mm08 liked post by shooternz On thread : Any ideas? Cratered primers and looks as though the strike is all over the primer

   Getting the firing pin bushed will sort that out any decent Gunsmith can do it.

   Liked On: 28-07-2022, 12:38 AM

10. 
    Kelton liked post by shooternz On thread : Any ideas? Cratered primers and looks as though the strike is all over the primer

    Getting the firing pin bushed will sort that out any decent Gunsmith can do it.

    Liked On: 27-07-2022, 02:52 PM

11. 
    Micky Duck liked post by shooternz On thread : .303 Learnings

    I scored a couple of plastic containers of 2201 years ago after CAC switched to other more suitable powder, They even loaded 243 and 270 with 2201 until they got surplus 4831, Shot up all the 2201...

    Liked On: 25-07-2022, 08:56 PM

12. 
    Micky Duck liked post by shooternz On thread : 45 colt mold wanted 200gn

    The Lyman 454424 was designed by Elmer Keith for the .45 Colt SA before it was chambered in Rifles the case of the modern .45 Colt was redesigned in 1909 for the Colt New Service DA Revolver before...

    Liked On: 24-07-2022, 07:09 PM

13. 
    Micky Duck liked post by shooternz On thread : Cast .44 loads

    That's handy in my Hood, Just setting up my Dillon 550 to load .44 mags

    Liked On: 23-07-2022, 10:32 AM

14. 
    Micky Duck liked post by shooternz On thread : Anyone familiar with these projectiles?

    They maybe equivalent burning rate but they are not the same specially in a .22 Hornet case capacity one tenth of a grain is a lot in that small case, It was originally a black powder cartridge...

    Liked On: 22-07-2022, 07:39 PM

15. 
    Micky Duck liked post by shooternz On thread : Cast .44 loads

    Not a good Idea max load for 2205/4227 is 22.5 grains better to start at 20.0 grains and work up you only need to load 3 of each to check pressure and accuracy to start, That is what I do and then...

    Liked On: 22-07-2022, 12:45 PM

Page 9 of 66 First 123456789101112131415161718192021222359 ... Last

• Jump to page: