shooternz
Member

979 Likes

Page 16 of 66 First ... 23456789101112131415161718192021222324252627282930 ... Last

• Jump to page:

1. 
   mikee liked post by shooternz On thread : Who Is Using 350 Legend ?

   I know you are after a 350 Legend but Winchester dropped the ball with it unless you are an AR15 user, Have you thought about a .358 Winchester better selection of bullet weights, I do cast .358's...

   Liked On: 26-11-2021, 07:10 PM

2. 
   Bill999 liked post by shooternz On thread : Who Is Using 350 Legend ?

   I know you are after a 350 Legend but Winchester dropped the ball with it unless you are an AR15 user, Have you thought about a .358 Winchester better selection of bullet weights, I do cast .358's...

   Liked On: 26-11-2021, 06:30 PM

3. 
   CBH Australia liked post by shooternz On thread : Cartridge suggestions

   Take a look at the 7x64 / 280 Rem 30/06 like the .308 case based cartridges on steroids with out the recoil , My pick would be the 7x64 with Norma ammo if factory is what you will be shooting most.

   Liked On: 23-11-2021, 12:13 AM

4. 
   17brno liked post by shooternz On thread : Trying something, Eric Cortina method of load development

   My F class rifles clean cold bore shots are 1 MOA low for my first sighter I add ! MOA elevation and take it off for the second if your wind call is correct you get 2 keepers very handy in the F...

   Liked On: 14-11-2021, 01:24 PM

5. 
   Backsteaks liked post by shooternz On thread : Cartridge suggestions

   Take a look at the 7x64 / 280 Rem 30/06 like the .308 case based cartridges on steroids with out the recoil , My pick would be the 7x64 with Norma ammo if factory is what you will be shooting most.

   Liked On: 11-11-2021, 05:49 PM

6. 
   tnankie liked post by shooternz On thread : Cartridge suggestions

   Take a look at the 7x64 / 280 Rem 30/06 like the .308 case based cartridges on steroids with out the recoil , My pick would be the 7x64 with Norma ammo if factory is what you will be shooting most.

   Liked On: 11-11-2021, 05:29 PM

7. 
   Micky Duck liked post by shooternz On thread : 9.3x62 loads

   If you want to save your shoulder I can supply you with some 292 grain cast bullets I shoot them at around 1400fps with 18.0 grains of Trail Boss, About to move up to 2208 in the next week or so,

   Liked On: 07-11-2021, 09:04 PM

8. 
   Moa Hunter liked post by shooternz On thread : Twist rate relative to barrel length

   No problem, barrel length has very little if any effect on stability Prime example is the ,38/.357 mag S&W barrels are 1:18 3/4" twist they will stabilise 195 grain bullets with barrels 2" to 8...

   Liked On: 25-10-2021, 10:00 AM

9. 
   johnd liked post by shooternz On thread : Trying something, Eric Cortina method of load development

   My F class rifles clean cold bore shots are 1 MOA low for my first sighter I add ! MOA elevation and take it off for the second if your wind call is correct you get 2 keepers very handy in the F...

   Liked On: 19-10-2021, 12:45 PM

10. 
    7mmwsm liked post by shooternz On thread : Twist rate relative to barrel length

    No problem, barrel length has very little if any effect on stability Prime example is the ,38/.357 mag S&W barrels are 1:18 3/4" twist they will stabilise 195 grain bullets with barrels 2" to 8...

    Liked On: 16-10-2021, 07:48 PM

11. 
    tetawa liked post by shooternz On thread : Twist rate relative to barrel length

    No problem, barrel length has very little if any effect on stability Prime example is the ,38/.357 mag S&W barrels are 1:18 3/4" twist they will stabilise 195 grain bullets with barrels 2" to 8...

    Liked On: 16-10-2021, 07:15 PM

12. 
    Tim Dicko liked post by shooternz On thread : Trimmer upgrade

    Hi Guys I want to upgrade my Wilson case trimmer with a power drive anyone using an electric screwdriver for this job on their trimmers Cheers Robert.

    Liked On: 13-10-2021, 08:48 PM

13. 
    Micky Duck liked post by shooternz On thread : 357 mag subsonic reloading data

    You are not going to get flash over or S.E.E in a pistol cartridge; do not open flash holes in any case all it does is stuff the case, The reason your ES open up is the pressure drop below its...

    Liked On: 11-10-2021, 07:32 PM

14. 
    Micky Duck liked post by shooternz On thread : The Lever Aficionados Thread

    Standard twist for the 7.62x39 is 1:9.5" .303 1:10" no real difference re-chambering the Baikal is the only to get a new .303 with out costing a pile of cash

    Liked On: 09-10-2021, 08:04 PM

15. 
    Pete_D liked post by shooternz On thread : Bench Mark 8208 powder and the .303

    Yes they are very close 8208 is excellent for powder throwers I load a pile of .223 Rem on my Dillon 550 with it very consistent powder weights.

    Liked On: 30-09-2021, 08:00 AM

Page 16 of 66 First ... 23456789101112131415161718192021222324252627282930 ... Last

• Jump to page: