shooternz
Member

979 Likes

Page 25 of 66 First ... 1112131415161718192021222324252627282930313233343536373839 ... Last

• Jump to page:

1. 
   NRT liked post by shooternz On thread : Bullet pulling related question

   A few kernels of powder will not make the slightest bit of difference in a load of powder for a 260 it is well within the margin of error of your powder weighing device, And your neck tension is...

   Liked On: 06-03-2021, 03:45 AM

2. 
   Kiwi Sapper liked post by shooternz On thread : "Air space" in 303 British and 308 Winchester caseloads...Dangerous?

   I suguest you buy a reloading manual preferably put out by the manufacture of the projectiles you are using, load your ammo with the overall length as given and the start load and work up in 0.5...

   Liked On: 24-02-2021, 09:43 AM

3. 
   Micky Duck liked post by shooternz On thread : 308 Subsonics

   Get hold of Dean Maisey Tauranga gunsmith he loads sub sonic .308s Also Mark Bridgman at Custom Cartridges Taupo

   Liked On: 31-01-2021, 05:02 PM

4. 
   Tommy liked post by shooternz On thread : Lee Loader .303 - what size scoop did Lee include?

   Yep that has been done a hang over from the black powder days, A friend use to load .38 Specials with a scoop made from a cut down case with a handle soldered on worked well,

   Liked On: 19-01-2021, 06:39 PM

5. 
   6x47 liked post by shooternz On thread : Reloading press

   Redding big Boss 11 is the prince of single stage presses and the Ultramag is king, Any of the O presses will handle 3.6" just buy the best you can it will out last your grand kids, I have an RCBS...

   Liked On: 19-01-2021, 07:33 AM

6. 
   Cordite liked post by shooternz On thread : Lee Loader .303 - what size scoop did Lee include?

   Yep that has been done a hang over from the black powder days, A friend use to load .38 Specials with a scoop made from a cut down case with a handle soldered on worked well,

   Liked On: 17-01-2021, 02:58 PM

7. 
   grandpamac liked post by shooternz On thread : Winchester 760 7-08

   WW760 was the powder factory ammo was loaded with when the 7mm08 was introduced in 1980 still a good choice just find a load from the projectile manufacturer you are using and you can't go wrong.

   Liked On: 15-01-2021, 09:12 AM

8. 
   Moa Hunter liked post by shooternz On thread : Trying something, Eric Cortina method of load development

   My F class rifles clean cold bore shots are 1 MOA low for my first sighter I add ! MOA elevation and take it off for the second if your wind call is correct you get 2 keepers very handy in the F...

   Liked On: 15-01-2021, 07:10 AM

9. 
   Padox liked post by shooternz On thread : Reloading press

   Redding big Boss 11 is the prince of single stage presses and the Ultramag is king, Any of the O presses will handle 3.6" just buy the best you can it will out last your grand kids, I have an RCBS...

   Liked On: 15-01-2021, 01:58 AM

10. 
    Beanie liked post by shooternz On thread : 357 Rossi loads 16inch

    Go for 158 HP the lighter bullet weights are for self defence and are really too fragile for animals if you reload cast bullets are economical.

    Liked On: 07-01-2021, 01:25 PM

11. 
    Tikka7mm08 liked post by shooternz On thread : Graphite wearing barrels

    I would think graphite is much the same as the moly coating craze that swept the shooting world a few years ago if anything it would lower the friction in the neck a little may make it more...

    Liked On: 05-01-2021, 03:20 PM

12. 
    Phil_H liked post by shooternz On thread : Graphite wearing barrels

    I would think graphite is much the same as the moly coating craze that swept the shooting world a few years ago if anything it would lower the friction in the neck a little may make it more...

    Liked On: 05-01-2021, 01:28 PM

13. 
    Cordite liked post by shooternz On thread : Graphite wearing barrels

    I would think graphite is much the same as the moly coating craze that swept the shooting world a few years ago if anything it would lower the friction in the neck a little may make it more...

    Liked On: 05-01-2021, 11:49 AM

14. 
    Nathanfish liked post by shooternz On thread : .303 Cast bullets

    Hi Guy's I have bought a new mould for the .303 It casts a 210 grain bullet .314" with a .304" nose only have a few hundred due to Gas Checks being unavailable at present Get in touch if you...

    Liked On: 02-01-2021, 07:31 PM

15. 
    Kiwi Sapper liked post by shooternz On thread : .303 Cast bullets

    Hi Guy's I have bought a new mould for the .303 It casts a 210 grain bullet .314" with a .304" nose only have a few hundred due to Gas Checks being unavailable at present Get in touch if you...

    Liked On: 02-01-2021, 07:25 PM

Page 25 of 66 First ... 1112131415161718192021222324252627282930313233343536373839 ... Last

• Jump to page: