shooternz
Member

979 Likes

Page 27 of 66 First ... 1314151617181920212223242526272829303132333435363738394041 ... Last

• Jump to page:

1. 
   Bos liked post by shooternz On thread : Load Testing Analysis. What do i make of this?

   Why did you not start with the projectile seated to manufacturers specs? They spend millions and hours working with highly sophisticated equipment and some first time loader thinks they know...

   Liked On: 02-11-2020, 12:51 PM

2. 
   7RMBoy liked post by shooternz On thread : Load Testing Analysis. What do i make of this?

   Why did you not start with the projectile seated to manufacturers specs? They spend millions and hours working with highly sophisticated equipment and some first time loader thinks they know...

   Liked On: 02-11-2020, 06:34 AM

3. 
   Micky Duck liked post by shooternz On thread : Minimium amount the projectile should be seated inside the neck of the case

   also recently have heard short seating CAN lead to a doughnut forming in neck area...took me awhile to work this out,believe the pressure of powder etc will push base of neck out more than the bit...

   Liked On: 23-10-2020, 08:04 PM

4. 
   Marty Henry liked post by shooternz On thread : A conundrum

   Lyman cast bullet manual list 24 grains of IMR 4198 with their 375248 mould 249gr FP as the accurate load, I have that mould and it has proved to be very accurate in a number of guns, I would be...

   Liked On: 20-10-2020, 09:36 PM

5. 
   Micky Duck liked post by shooternz On thread : A conundrum

   Lyman cast bullet manual list 24 grains of IMR 4198 with their 375248 mould 249gr FP as the accurate load, I have that mould and it has proved to be very accurate in a number of guns, I would be...

   Liked On: 20-10-2020, 07:46 PM

6. 
   mimms2 liked post by shooternz On thread : reloading lead pills

   The .22 Hornet with 10.0 grains of Lil'gun is the way to go, They are to short in the .223

   Liked On: 12-10-2020, 06:49 AM

7. 
   Tuidog liked post by shooternz On thread : 2213sc in 6.5x55?

   I use 2213sc in an F class rifle 30" barrel with Lapua 139 match bullets velocity was 2927fps in my Sako 75 velocity 2560fps with 46.6 grains with much better accuracy than 2209 it is not maximin...

   Liked On: 11-10-2020, 01:32 PM

8. 
   Micky Duck liked post by shooternz On thread : 44 mag AP70 loads

   I have a 215Grain HP for the 44/40 would probably kill a hare, no GC but good for 1200- 1300fps

   Liked On: 03-10-2020, 09:24 PM

9. 
   Micky Duck liked post by shooternz On thread : QuickLoad?

   Not any more ADI makes all three been verified by a couple of guys shooting all three powders in .44 mag revolvers at HMS matches same load same bullet same velocity, It is an excellent powder for...

   Liked On: 03-10-2020, 06:36 PM

10. 
    Micky Duck liked post by shooternz On thread : Lee 358-158-RF and Other Bullets

    You are on the right track, My bullets are cast as soft as possible to get expansion HP's are necessary for 1100Fps or less; over that 50/50 wheel weights and pure lead will expand well with out a...

    Liked On: 21-09-2020, 08:13 PM

11. 
    veitnamcam liked post by shooternz On thread : Subsonic action

    At subsonic it should never foul just clean with solvent and a few patches it is like a big .22RF, The lube is mostly wax a bit like car wax, all that is in the bore is powder residue no scrubbing...

    Liked On: 18-09-2020, 07:44 PM

12. 
    Rated M for Magnum liked post by shooternz On thread : IMR 4064 in 308

    Hornady list IMR 4064 with a 162 grain from 32.3 to 39.6 very close to 2208, I used it years ago for target loads in .308's with 168 MK great powder a little coarse grained

    Liked On: 18-09-2020, 12:33 PM

13. 
    Tommy liked post by shooternz On thread : Reloading Finocchi 380 / 9 x 17 salve = blank ..............Whatever that means.

    Drilling out the primer pocket for shotgun primers works well did it to a .22 Hornet and shot air rifle pellets with it would be ok in a .380 plenty loud enough

    Liked On: 16-09-2020, 09:06 PM

14. 
    Micky Duck liked post by shooternz On thread : Reloading Finocchi 380 / 9 x 17 salve = blank ..............Whatever that means.

    Drilling out the primer pocket for shotgun primers works well did it to a .22 Hornet and shot air rifle pellets with it would be ok in a .380 plenty loud enough

    Liked On: 16-09-2020, 08:52 PM

15. 
    Teggy liked post by shooternz On thread : 7.5x55 swiss

    I have loaded for one not your typical K31 mine has a 1:13" Tru elite barrel I shoot Sierra 155 PALMA in it, Your groove diameter is .306" and bore is .297" so take care working up loads the Sierra...

    Liked On: 10-09-2020, 12:21 AM

Page 27 of 66 First ... 1314151617181920212223242526272829303132333435363738394041 ... Last

• Jump to page: