SimonJDH
Member

27 Likes

Page 1 of 2 12 Last

• Jump to page:

1. 
   SimonJDH liked post by Pengy On thread : Clip on NV help

   https://youtu.be/_e-NqqeYh18

   Liked On: 11-07-2022, 05:21 PM

2. 
   SimonJDH liked post by Huntertoo On thread : Clip on NV help

   I run a 007a on three rifles too. I’ve got a 48mm adaptor and use different thickness’s of alkathene pipe as sleeves. just like the pic above. Works well.

   Liked On: 11-07-2022, 05:21 PM

3. 
   SimonJDH liked post by Trout On thread : Clip on NV help

   You dont have to have a flash day scope.Its the specs that are important.Generally i can dial up to 4x and shoot deer out to 300yds.My daughter is bringing up my new burris scope today($400)2.5-10x42...

   Liked On: 11-07-2022, 05:20 PM

4. 
   SimonJDH liked post by zeropak On thread : Clip on NV help

   Good feedback. also from Trout. Its great to get this feedback from people who have actually used one. Certainly the forward clipon has a lot of great features. Can you tell me more about scope...

   Liked On: 11-07-2022, 09:51 AM

5. 
   SimonJDH liked post by zeropak On thread : Clip on NV help

   Ok, Interesting. there is a conflicting info online about changing scope zero's with a forward NV or thermal attached. I guess the other real issue is cost. You can get a Sytong or Pard rear NV...

   Liked On: 11-07-2022, 09:51 AM

6. 
   SimonJDH liked post by Larskramer On thread : Clip on NV help

   I've had my forward clipon shoot from my zero at 100m, to dialed up at 327m and still hit square on where my cross hairs were.

   Liked On: 11-07-2022, 09:51 AM

7. 
   SimonJDH liked post by Trout On thread : Clip on NV help

   Chat to Peter (The Hunters Corner)He will see you right,a lot of guys have brought off him on here including me.

   Liked On: 10-07-2022, 08:17 PM

8. 
   SimonJDH liked post by Trout On thread : Clip on NV help

   On TM theres a InFiRay CH50V2,buitifull unit design for scopes up to 9x.I know iv got one.Will get it on a new burris scope next week.Both have the same fov and the scope is a 2.5x10x42.Iv got a...

   Liked On: 10-07-2022, 06:49 PM

9. 
   SimonJDH liked post by zeropak On thread : Clip on NV help

   The issue with a forward clip is the change of zero that will most likely occur. Although admittedly I haven't used one I did quite a bit of research on this before going to the rear attachment...

   Liked On: 10-07-2022, 06:49 PM

10. 
    SimonJDH liked post by TLB On thread : Clip on NV help

    I think I have only seen one forward mounted NV unit from memory. It was a pulsar, certainly not common at all to have a forward mounted NV unit.

    Liked On: 10-07-2022, 11:21 AM

11. 
    SimonJDH liked post by TLB On thread : Clip on NV help

    It will work fine. You get 1 adapter with the unit so depending on your ocular diameter is whether or not you'll need another adapter. Big plus with the night vision over the thermal is you can...

    Liked On: 10-07-2022, 11:18 AM

12. 
    SimonJDH liked post by Trout On thread : Clip on NV help

    Ok if you into NV,get a forward clip on,far less hassel than a rear clip on. Enjoy.

    Liked On: 10-07-2022, 11:04 AM

13. 
    SimonJDH liked post by Marty Henry On thread : Clip on NV help

    A limbsaver slip on recoil pad will fix the eye relief problem. Thermal is a whole different ballgame and much more expensive, I have a thermal monocular and nv and find the combination works very...

    Liked On: 10-07-2022, 10:06 AM

14. 
    SimonJDH liked post by Trout On thread : Clip on NV help

    Get a forward thermal clip on,have a fixed parralax on scope and get adaptor near the same size as yr objective bell.Yr clip on will centralize to yr scope nicely.Have a scope with a 1.5 to 2.5 low...

    Liked On: 10-07-2022, 10:06 AM

15. 
    SimonJDH liked post by Larskramer On thread : Clip on NV help

    I've used a few resr clip on.. my biggest problem is the extra length towards your eye. I prefer my thermal forward clip on. That's great!

    Liked On: 10-07-2022, 10:05 AM

Page 1 of 2 12 Last

• Jump to page: