SixtyTen
Member

449 Likes

Page 13 of 30 First 123456789101112131415161718192021222324252627 ... Last

• Jump to page:

1. 
   Moa Hunter liked post by SixtyTen On thread : Hand me down Model 70

   Fantastic project for a young fella. I would make one recommendation when doing the bluing to avoid disappointment. CLEANLINESS. Go way further than you think is reasonable. Once you have the parts...

   Liked On: 23-05-2022, 02:26 PM

2. 
   ROKTOY liked post by SixtyTen On thread : Hand me down Model 70

   Fantastic project for a young fella. I would make one recommendation when doing the bluing to avoid disappointment. CLEANLINESS. Go way further than you think is reasonable. Once you have the parts...

   Liked On: 22-05-2022, 11:25 PM

3. 
   Joe_90 liked post by SixtyTen On thread : Hand me down Model 70

   Fantastic project for a young fella. I would make one recommendation when doing the bluing to avoid disappointment. CLEANLINESS. Go way further than you think is reasonable. Once you have the parts...

   Liked On: 22-05-2022, 11:22 PM

4. 
   veitnamcam liked post by SixtyTen On thread : Hand me down Model 70

   Fantastic project for a young fella. I would make one recommendation when doing the bluing to avoid disappointment. CLEANLINESS. Go way further than you think is reasonable. Once you have the parts...

   Liked On: 22-05-2022, 10:50 PM

5. 
   20 Bore liked post by SixtyTen On thread : DIY Induction Annealer

   I have built multiple induction annealers using induction boards, power supplies and timers from Ebay. Total cost in parts to make one is generally around $400NZD Latest one has an auto feed with...

   Liked On: 16-05-2022, 07:47 PM

6. 
   jake8587 liked post by SixtyTen On thread : DIY Induction Annealer

   I have built multiple induction annealers using induction boards, power supplies and timers from Ebay. Total cost in parts to make one is generally around $400NZD Latest one has an auto feed with...

   Liked On: 16-05-2022, 02:31 PM

7. 
   dannyb liked post by SixtyTen On thread : DIY Induction Annealer

   I have built multiple induction annealers using induction boards, power supplies and timers from Ebay. Total cost in parts to make one is generally around $400NZD Latest one has an auto feed with...

   Liked On: 15-05-2022, 01:07 PM

8. 
   Hunter_Nick liked post by SixtyTen On thread : Walnut stock build (done the traditional way)

   Wow.

   Liked On: 07-05-2022, 01:03 PM

9. 
   40mm liked post by SixtyTen On thread : How to bend 40mm copper pipe 180° ?

   I bent some 25mm steel tube for a motorbike into a tight U bend a number of years back. I flattened and folded over one end, packed the tube as full as possible with sand (like compress it in there...

   Liked On: 05-05-2022, 09:05 PM

10. 
    dannyb liked post by SixtyTen On thread : How to bend 40mm copper pipe 180° ?

    I bent some 25mm steel tube for a motorbike into a tight U bend a number of years back. I flattened and folded over one end, packed the tube as full as possible with sand (like compress it in there...

    Liked On: 05-05-2022, 05:30 PM

11. 
    Joe_90 liked post by SixtyTen On thread : Confusing pressure signs

    Might be your low enough to get into the dangerous reduced loads territory, where you get random pressure spikes. I can't explain exactly what is happening with certain reduced loads that create...

    Liked On: 17-04-2022, 09:52 PM

12. 
    Cordite liked post by SixtyTen On thread : Mags

    I have 3d printed a bunch of mags for various different rifles, center-fire and rimfire. I have found it generally takes at least 5 or 6 versions to get the geometry perfect, and that is with an...

    Liked On: 08-03-2022, 07:05 PM

13. 
    Micky Duck liked post by SixtyTen On thread : Starting load development and would love help

    Im also using the 165 Gameking and 2206H. 42gr gets me 2600 from a cut down 16" Parkerhale TX1200 (Mauser 98 action). I tested up to 43.5gr and was getting FLAT primers in cold (5c) weather, a load...

    Liked On: 05-03-2022, 09:23 PM

14. 
    Micky Duck liked post by SixtyTen On thread : Mags

    I have 3d printed a bunch of mags for various different rifles, center-fire and rimfire. I have found it generally takes at least 5 or 6 versions to get the geometry perfect, and that is with an...

    Liked On: 05-03-2022, 12:50 PM

15. 
    Hunter_Nick liked post by SixtyTen On thread : Walnut stock build (done the traditional way)

    Wow, that's amazing. I really like the trigger guard relief, very nice touch. I have made a few stocks over the years, and can say without a shadow of a doubt that I do not have the patience required...

    Liked On: 10-02-2022, 10:55 PM

Page 13 of 30 First 123456789101112131415161718192021222324252627 ... Last

• Jump to page: