Great info, thanks for that. I spent ages looking for something to add some texture to mine, from nonskid grit for boats to truck bed liner. Never though about using this underneath a colored top...
Liked On: 20-04-2024, 03:12 PM
Hello Gents, I recently purchased a 7mm Rem Mag Browning X-Bolt and also bought some once fired Norma brass off Trademe. I found that the cases all had a bad bulge right in front of the belt....
Liked On: 13-04-2024, 09:30 PM
Hello Gents, I recently purchased a 7mm Rem Mag Browning X-Bolt and also bought some once fired Norma brass off Trademe. I found that the cases all had a bad bulge right in front of the belt....
Liked On: 13-04-2024, 06:07 PM
Hey Folks, I thought this could be useful and might interest a few here. I read about this technique on another forum and decided to give it a go. I wanted to make a chamber cast of my No1mk3...
Liked On: 10-03-2024, 03:21 PM
I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....
Liked On: 21-02-2024, 09:06 PM
Yeah, I was limited in size for this one because of the front sight. I'm tossing up putting a red dot or small scope on it as my eyes are not the best. If I did that, I would likely remove the front...
Liked On: 17-02-2024, 02:53 PM
I made a suppressor for this a while back and have not shot it since making it. So I took it along to the range on the weekend to sort out a load for it and see how it shoots with a suppressor. ...
Liked On: 07-02-2024, 10:18 PM
I made a suppressor for this a while back and have not shot it since making it. So I took it along to the range on the weekend to sort out a load for it and see how it shoots with a suppressor. ...
Liked On: 07-02-2024, 08:31 PM
I made a suppressor for this a while back and have not shot it since making it. So I took it along to the range on the weekend to sort out a load for it and see how it shoots with a suppressor. ...
Liked On: 07-02-2024, 10:25 AM
I made a suppressor for this a while back and have not shot it since making it. So I took it along to the range on the weekend to sort out a load for it and see how it shoots with a suppressor. ...
Liked On: 06-02-2024, 09:01 PM
Wow, those look fantastic. Nice work on the checkering, it's not easy and most don't have the patience for it. I have checkered a couple of stocks and it will take a very special project to get me to...
Liked On: 31-01-2024, 01:08 PM
I have a bunch of threaded inserts in the bench top https://www.anzor.co.nz/threaded-inserts/wood-threaded-inserts/m6-304-wood-insert I came up with a 4 bolt pattern (150x75 from memory) and...
Liked On: 01-01-2024, 09:13 AM
Cheers, I will be using it for service rifle and already have some Speer 140s to try as they are the cheapest 6.5 proj in NZ I can find. I also want a load for longer range, so will be working on...
Liked On: 21-12-2023, 03:02 AM
Cheers, I will be using it for service rifle and already have some Speer 140s to try as they are the cheapest 6.5 proj in NZ I can find. I also want a load for longer range, so will be working on...
Liked On: 20-12-2023, 10:40 PM
I have an M38 Swedish Mauser on the way and will be reloading for it. I'm planning to use 140gr HPBT projectiles and trying to match the service load velocity (from what I understand this is around...
Liked On: 17-12-2023, 07:48 PM