SixtyTen
Member

449 Likes

Page 17 of 30 First ... 3456789101112131415161718192021222324252627282930 Last

• Jump to page:

1. 
   hamsav liked post by SixtyTen On thread : Casting for an SMLE

   I think you are correct about just trying some standard ammo and see. Fact is this is probably not going to get shot very often, and I'm not competing with it. Problem is I can't help but tinker with...

   Liked On: 14-12-2021, 06:48 AM

2. 
   rossi.45 liked post by SixtyTen On thread : Casting for an SMLE

   I think you are correct about just trying some standard ammo and see. Fact is this is probably not going to get shot very often, and I'm not competing with it. Problem is I can't help but tinker with...

   Liked On: 13-12-2021, 09:47 PM

3. 
   rossi.45 liked post by SixtyTen On thread : Casting for an SMLE

   Hey Folks, I have a couple of 1943 (or 1946, hard to tell) Lithgow No1Mk3*s, one of which had a full wood and hardware set, but a completely corroded bore, and the other that has a badly sportered...

   Liked On: 13-12-2021, 09:45 PM

4. 
   40mm liked post by SixtyTen On thread : Casting for an SMLE

   Hey Folks, I have a couple of 1943 (or 1946, hard to tell) Lithgow No1Mk3*s, one of which had a full wood and hardware set, but a completely corroded bore, and the other that has a badly sportered...

   Liked On: 13-12-2021, 07:51 PM

5. 
   grandpamac liked post by SixtyTen On thread : More Learnings and Questions Using Redding Competition Shell Holders.

   Beer/coke cans are almost exactly 0.1mm. Be easy to cut a couple of washers from that to test the idea and then wrangle up something a little harder as the permanent fix.

   Liked On: 13-12-2021, 06:36 PM

6. 
   20 Bore liked post by SixtyTen On thread : CZ 527 3 round magazine modification

   Awesome, nice job. I have done something similar with plastic Howa mini magazines.

   Liked On: 07-12-2021, 06:11 PM

7. 
   40mm liked post by SixtyTen On thread : Ar-15 Dedicated 22lr upper, using CMMG bolt

   Thanks! A majority of my gunsmithing work is lathe based. The one I bought was about $2000 brand new plus about $1000 in tooling. So it's not completely out of reach for most people to buy one. When...

   Liked On: 13-11-2021, 07:06 AM

8. 
   40mm liked post by SixtyTen On thread : Ar-15 Dedicated 22lr upper, using CMMG bolt

   Hi everyone, this is a project I recently finished. The plan was to build a dedicated 22lr upper using a standard ar15 upper, a modified CMMG conversion bolt and a used Anschutz 520 barrel. It...

   Liked On: 13-11-2021, 07:05 AM

9. 
   Fssprecision liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

   I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....

   Liked On: 30-10-2021, 06:41 PM

10. 
    Moa Hunter liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

    I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....

    Liked On: 30-10-2021, 08:55 AM

11. 
    gundoc liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

    I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....

    Liked On: 30-10-2021, 05:16 AM

12. 
    257weatherby liked post by SixtyTen On thread : Weatherby becomes a gunsmith!

    Nice job, I quite enjoy diagnosing feed, extraction and ejection problems with rifles. Its often very small things and can be quite challenging. I got a cheap CZ452 .22lr that would not extract fired...

    Liked On: 07-10-2021, 07:52 PM

13. 
    Sideshow liked post by SixtyTen On thread : Weatherby becomes a gunsmith!

    Nice job, I quite enjoy diagnosing feed, extraction and ejection problems with rifles. Its often very small things and can be quite challenging. I got a cheap CZ452 .22lr that would not extract fired...

    Liked On: 07-10-2021, 07:19 PM

14. 
    Fssprecision liked post by SixtyTen On thread : An old one sympathetically bough back

    Awesome, nice job. Id like to see how it shoots. Thanks for posting.

    Liked On: 03-10-2021, 09:56 AM

15. 
    Preacher liked post by SixtyTen On thread : Home ‘bluing’

    I have used duracoat on a few rifles now. Easy enough to apply with a spray gun and seems to be holding up fine. It tool a long time to cure properly completely and stop out-gassing (as in my gunsafe...

    Liked On: 09-09-2021, 02:41 PM

Page 17 of 30 First ... 3456789101112131415161718192021222324252627282930 Last

• Jump to page: