SixtyTen
Member

391 Likes

Page 19 of 27 First ... 56789101112131415161718192021222324252627 Last

• Jump to page:

1. 
   SixtyTen liked post by akaroa1 On thread : Elliot Model 5 tool and cutter grinder

   This Elliot Model 5 tool and cutter grinder just arrived in time for a play during the long weekend 169385 It came with an original dust extraction unit most of the original attachments ...

   Liked On: 05-06-2021, 11:38 AM

2. 
   SixtyTen liked post by akaroa1 On thread : Elliot Model 5 tool and cutter grinder

   And lots of parts with it to work out like a jigsaw puzzle Also came with a huge magnetic table as it was being mainly used as a surface grinder 169420

   Liked On: 05-06-2021, 11:38 AM

3. 
   SixtyTen liked post by Hunter_Nick On thread : Build yourself a fibreglass stock

   Step eight The good sh*t!! Right lads, time to really roll up the sleeves and get serious! It’s time to build a stock. Mould prep is slightly different at this stage, still the same 4 coats of...

   Liked On: 04-06-2021, 05:00 PM

4. 
   SixtyTen liked post by Hunter_Nick On thread : Build yourself a fibreglass stock

   Step seven Prep the mould Because I’m pretty OCD, I got some 1500grit wet and dry and polished up the inside mould surfaces. There was slight grain patterns left from the original, so I cut that...

   Liked On: 04-06-2021, 04:57 PM

5. 
   SixtyTen liked post by Hunter_Nick On thread : Build yourself a fibreglass stock

   The moment of truth!!!!! Splitting the mould After another 24 hours, you are now ready for one of the most exciting parts! Very gently start to pry the two halves of the mould apart. I find a...

   Liked On: 04-06-2021, 04:57 PM

6. 
   SixtyTen liked post by Hunter_Nick On thread : Build yourself a fibreglass stock

   Step five Remove parting board Once the first side has set (24 hours) gently remove the parting board leaving the stock in place attached to the first mould half. With any luck it will pop off...

   Liked On: 04-06-2021, 04:56 PM

7. 
   SixtyTen liked post by Hunter_Nick On thread : Build yourself a fibreglass stock

   Step four Create the first mould half A good layer of release wax is required now. Use as per the manufacturer instructions, I used 4 coats. Then a a good layer of heavy hold hairspray and you’re...

   Liked On: 04-06-2021, 04:55 PM

8. 
   SixtyTen liked post by ebf On thread : Baikal single shot rebarrel - Anyone done this?

   Awesome work :thumbsup:

   Liked On: 02-06-2021, 10:46 PM

9. 
   SixtyTen liked post by Micky Duck On thread : Baikal single shot rebarrel - Anyone done this?

   Rifle - ADI World Class Powders and Ammunition (http://www.adi-powders.com.au/rifle/45-70-government-trapdoor-rifles) these are good load info...its the bottom tier...the lower pressure loads for...

   Liked On: 25-05-2021, 10:15 PM

10. 
    SixtyTen liked post by Micky Duck On thread : Baikal single shot rebarrel - Anyone done this?

    168496

    Liked On: 25-05-2021, 06:40 PM

11. 
    SixtyTen liked post by Micky Duck On thread : Baikal single shot rebarrel - Anyone done this?

    interesting.....there is much easier way to do this... will flick you a PM.

    Liked On: 24-05-2021, 06:28 PM

12. 
    SixtyTen liked post by Woody On thread : Making a shooting Tripod

    These days I find it a little more difficult to hold steady unsupported when a prone position is bot an option. I spotted a bit of guff on YT and sifted thru a bunch of bandwagon salemen and some...

    Liked On: 17-05-2021, 04:54 PM

13. 
    SixtyTen liked post by akaroa1 On thread : American long rifle build

    I put 20 shots down range today from the American long rifle This image is a cluster of shots from a bench at 55m Every few shots I took another 0.5mm off the front sight Slowly brought it up...

    Liked On: 16-04-2021, 08:05 PM

14. 
    SixtyTen liked post by akaroa1 On thread : American long rifle build

    100 % finished Steel trigger guard makes it complete 165137

    Liked On: 16-04-2021, 08:03 PM

15. 
    SixtyTen liked post by akaroa1 On thread : American long rifle build

    Done Browning went very well and has nice deep old rust colour and texture Just needs a trigger guard big enough for the double triggers 164161164162164163164164164165164166164167164168

    Liked On: 01-04-2021, 03:47 PM

Page 19 of 27 First ... 56789101112131415161718192021222324252627 Last

• Jump to page: