SixtyTen
Member

569 Likes

Page 30 of 38 First ... 1617181920212223242526272829303132333435363738 Last

• Jump to page:

1. 
   Scout liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

   So it turns out the barrels are soldered in. I was trying to heat up the barrel shank to break the threads/press fit free and noticed the smell of solder flux and then with a bit more heat, had...

   Liked On: 25-05-2021, 08:36 PM

2. 
   takbok liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

   So it turns out the barrels are soldered in. I was trying to heat up the barrel shank to break the threads/press fit free and noticed the smell of solder flux and then with a bit more heat, had...

   Liked On: 25-05-2021, 07:15 PM

3. 
   Micky Duck liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

   I did, thanks for the info. I will likely be picking your brain some more once I get further along with this project.

   Liked On: 25-05-2021, 06:29 PM

4. 
   Cordite liked post by SixtyTen On thread : Tony Hawkin's and I wonder what happened to his rifling machine

   The best mechanical solution I have seen uses a gear rack attached to the "Cross slide" of the machine and an angled bar off the backside that the end of the rack is attached to. The gear is attached...

   Liked On: 15-05-2021, 10:25 AM

5. 
   Moa Hunter liked post by SixtyTen On thread : DIY Extended Bolt Knobs

   Hi Folks, I have done this to a bunch of rifles now and really like the results so I thought I would share it. Its a pretty simple method of adding an extended bolt knob using JB SteelStik. Its...

   Liked On: 16-12-2020, 05:54 PM

6. 
   Cyclops liked post by SixtyTen On thread : DIY Extended Bolt Knobs

   Hi Folks, I have done this to a bunch of rifles now and really like the results so I thought I would share it. Its a pretty simple method of adding an extended bolt knob using JB SteelStik. Its...

   Liked On: 16-12-2020, 05:53 PM

7. 
   Joe_90 liked post by SixtyTen On thread : DIY Extended Bolt Knobs

   Hi Folks, I have done this to a bunch of rifles now and really like the results so I thought I would share it. Its a pretty simple method of adding an extended bolt knob using JB SteelStik. Its...

   Liked On: 16-12-2020, 08:38 AM

8. 
   rugerman liked post by SixtyTen On thread : DIY Extended Bolt Knobs

   Hi Folks, I have done this to a bunch of rifles now and really like the results so I thought I would share it. Its a pretty simple method of adding an extended bolt knob using JB SteelStik. Its...

   Liked On: 16-12-2020, 07:55 AM

9. 
   Tentman liked post by SixtyTen On thread : DIY Extended Bolt Knobs

   Hi Folks, I have done this to a bunch of rifles now and really like the results so I thought I would share it. Its a pretty simple method of adding an extended bolt knob using JB SteelStik. Its...

   Liked On: 15-12-2020, 07:49 PM

10. 
    rupert liked post by SixtyTen On thread : DIY Extended Bolt Knobs

    Hi Folks, I have done this to a bunch of rifles now and really like the results so I thought I would share it. Its a pretty simple method of adding an extended bolt knob using JB SteelStik. Its...

    Liked On: 15-12-2020, 07:40 PM

11. 
    Ftx325 liked post by SixtyTen On thread : DIY Extended Bolt Knobs

    Hi Folks, I have done this to a bunch of rifles now and really like the results so I thought I would share it. Its a pretty simple method of adding an extended bolt knob using JB SteelStik. Its...

    Liked On: 15-12-2020, 06:59 PM

12. 
    Micky Duck liked post by SixtyTen On thread : Firearm licencing

    What a bunch of muppets. I went to hand a mail order form into the local station and had a 10 min conversation trying to explain to the stupid woman on the desk (a police officer) what her job was...

    Liked On: 16-11-2020, 08:05 PM

13. 
    RUMPY liked post by SixtyTen On thread : How to make a D-type reamer to chamber a barrel

    I made a chamber reamer for .357 sig a couple of days ago, and have made a couple of other chamber reamers and several projectile reamers using this technique. Gundoc has it right, except I tend...

    Liked On: 12-09-2020, 07:01 PM

14. 
    berg243 liked post by SixtyTen On thread : Taps and dies

    Second this. Prices are good and great quality. Shipping is reasonable and very fast turn around (I usually get stuff the day after I order it in Auckland) I actually made my own tap a little...

    Liked On: 18-08-2020, 11:00 PM

15. 
    takbok liked post by SixtyTen On thread : How to make a D-type reamer to chamber a barrel

    A removable pilot is not really required unless you are going to be chambering multiple barrels with variable bore sizes. For a one off job, just sizing the pilot to the barrel on hand is fine. I...

    Liked On: 16-08-2020, 05:46 PM

Page 30 of 38 First ... 1617181920212223242526272829303132333435363738 Last

• Jump to page: