SixtyTen
Member

391 Likes

Page 7 of 27 First 123456789101112131415161718192021 ... Last

• Jump to page:

1. 
   SixtyTen liked post by akaroa1 On thread : Turning a chamber reamer into a live pilot

   I just thought this might be a project that might help someone else out. I re barreled one of my vintage rifles recently. Had it dialed up in the lathe to cut the chamber and realised it's bore...

   Liked On: 13-08-2023, 03:19 PM

2. 
   SixtyTen liked post by viper On thread : My new hunting knife

   230892230893, Glad you like it. Designed primarily as a skinning knife. Made from AEB-L stainless steel. G10 bolsters and liners. The second picture is mine about to be put to work.

   Liked On: 12-08-2023, 09:19 PM

3. 
   SixtyTen liked post by Delphus On thread : First proper stock build complete

   Hey team I have finally completed my first attempt at a walnut stock. I was given a slab from a farmer mate and wanted to try my hand. It’s far from perfect, and a long way off some stocks on...

   Liked On: 09-07-2023, 05:57 PM

4. 
   SixtyTen liked post by akaroa1 On thread : Who needs to add serial numbers in CHCH?

   I recently got my own Engraving Pantograph and have started on the firearms I have that don't have any serial numbers. With the right gear it's actually pretty easy. If there are a few guys...

   Liked On: 09-07-2023, 05:55 PM

5. 
   SixtyTen liked post by nzfubz On thread : Target Camera

   Finally got all the pieces I needed to make a target camera. Range is out to 5km so will be suitable for all range and gong work. Have tried to list all the instructions so people can have a go...

   Liked On: 22-06-2023, 01:15 PM

6. 
   SixtyTen liked post by akaroa1 On thread : Wildcat appreciation thread

   My wildcat leaning is towards a 375 because of reasonable bullet options But it needs to be rimmed So I was thinking a 9.3x74R case necked up to 375 A nice sized good quality case but not as...

   Liked On: 18-06-2023, 10:25 PM

7. 
   SixtyTen liked post by Bushline On thread : Fires

   Must have been a (heat sika)

   Liked On: 22-05-2023, 07:55 PM

8. 
   SixtyTen liked post by gundoc On thread : Welding up/filling in screw holes on a P14 receiver.

   Countersink both sides of the holes, fit correct size steel screws to stick out about 3mm each side after the heads are cut off, peen both sides heavily against suitable anvils, then peen again at...

   Liked On: 23-04-2023, 05:05 PM

9. 
   SixtyTen liked post by akaroa1 On thread : Making 25 rimfire reloadable brass

   Put together 5 rounds to go for a late afternoon hunt Shot this hare at 45m 221219 Straight through the top of the heart and what a lot of damage 221220 So this evening I have done...

   Liked On: 15-04-2023, 09:25 AM

10. 
    SixtyTen liked post by akaroa1 On thread : Making 25 rimfire reloadable brass

    So now I want to go live fire Parted off 3x 120 grain 257 bullets to around 60 grains 221215 Sit them on 2.0 grains of trailboss First shot low and sub sonic Correct rear tang sight Next 2...

    Liked On: 15-04-2023, 09:24 AM

11. 
    SixtyTen liked post by akaroa1 On thread : Making 25 rimfire reloadable brass

    I got a very nice Winchester 1885 25 RF recently. Circa 1910 Very good condition mechanically and an excellent bore Original idea was chamber 25-20 and convert to center Fire. But it's so...

    Liked On: 15-04-2023, 09:23 AM

12. 
    SixtyTen liked post by rambo-6mmrem On thread : 6.5 Grendel 150gn cast bullet

    SixtyTen Max seat length is 2.261” Bullet length is 1.188” missing gas check so might be a few thou longer once fitted Arround 0.435 of bullet below the case mouth Bullet base is just below...

    Liked On: 10-04-2023, 10:22 PM

13. 
    SixtyTen liked post by RabbitStu On thread : 22lr Resizing/Hollow Pointing Tool

    Just a quicky note, I was and still am going to make a resizing tool for .22lr and while talking with a local gunsmith he advised me First to pillar and epoxy the the stock which for the rimfire I...

    Liked On: 06-04-2023, 09:49 AM

14. 
    SixtyTen liked post by Wingman On thread : Another .45acp Delisle Comando Carbine completed.

    Here's a special little build I just completed, a replica of the only known prototype of the Paratrooper Delisle Commando carbine built by Stirling. This one has the under folding Stirling SMG...

    Liked On: 17-03-2023, 08:27 AM

15. 
    SixtyTen liked post by Tall kiwi On thread : New shooter looking for a place to shoot near Auckland

    Cheers mate. I just received my FAL today in the mail and am planning on picking up my first .22 in the next few days. All going well I might try come along sometime in the next week or two :)

    Liked On: 11-03-2023, 04:22 PM

Page 7 of 27 First 123456789101112131415161718192021 ... Last

• Jump to page: