SixtyTen
Member

320 Likes

Page 10 of 22 First 12345678910111213141516171819202122 Last

• Jump to page:

1. 
   SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

   a small amount of lube on the base of the bullet . . you'd think it would leave a coating on the bore that the next bullet would run into and cause problems . . but it doesn'nt, i've never had...

   Liked On: 16-12-2021, 06:43 PM

2. 
   SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

   i have a cunning plan . . . looking at the 170grn. Lyman round nose and measuring the bore riding nose and pushing the nose into the bore, i see its just on .301 and leaves slight engraving, maybe...

   Liked On: 16-12-2021, 06:42 PM

3. 
   SixtyTen liked post by shooternz On thread : Casting for an SMLE

   Get in touch I have some .314" 210 grain cast if you want to try some

   Liked On: 16-12-2021, 06:11 PM

4. 
   SixtyTen liked post by Driverman On thread : Casting for an SMLE

   Im watching this thread with interest. Powdercoating is just a term for providing a polymer coating to a projectile The coating is a good deal harder than the lead and if done right will not leave a...

   Liked On: 14-12-2021, 04:23 PM

5. 
   SixtyTen liked post by Micky Duck On thread : Casting for an SMLE

   grab some cast ones off shootersnz / Robert and TRY them at standard size and just see..you may be making things harder than need be.

   Liked On: 14-12-2021, 04:22 PM

6. 
   SixtyTen liked post by Joe_90 On thread : Solving a Sako design fault

   Very nice work! When I saw the thread title I was half expecting to see a photo of a howa :D

   Liked On: 13-12-2021, 05:38 PM

7. 
   SixtyTen liked post by gundoc On thread : Solving a Sako design fault

   The Sako .22 P94S has a design fault in the bolt locking ring which can cause the bolt handle and locking lug to break off the bolt during opening. This problem is caused by a combination of a steep...

   Liked On: 13-12-2021, 05:34 PM

8. 
   SixtyTen liked post by Joe_90 On thread : Cast bullet Varminting / Medium game Project

   Would be good to try it for sure! Won't look as cool as the 230gr howitzer rounds though. If only I could get them shooting right :pissed off: 185473

   Liked On: 08-12-2021, 04:37 PM

9. 
   SixtyTen liked post by akaroa1 On thread : 303 vs 308

   This was today's project to get the front one of these 44 1/2s scope fitted Much more interesting and challenging 185331

   Liked On: 07-12-2021, 06:39 PM

10. 
    SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

    185436 SixtyTen i use a filler to keep the powder close to the primer, always have . . always do in any of my cast reloads for every caliber, others will have different ideas

    Liked On: 07-12-2021, 06:34 PM

11. 
    SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

    185410 100 31141 cast

    Liked On: 07-12-2021, 04:58 PM

12. 
    SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

    185408 1st bullets to try are 2 of my favourites from left, Lyman 31141 and 311291 both 170 grains . . 31141 i first tried in the 30/30 and proved very accurate and a good killer, 311291...

    Liked On: 07-12-2021, 04:58 PM

13. 
    SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

    185421 this is where i'm at now . . bullet sized, lubed, gas check, seated with a light crimp over 7.0 grains of Nobels No.2 powder, expecting just over 1,000fps next few days i will do a...

    Liked On: 07-12-2021, 04:42 PM

14. 
    SixtyTen liked post by Blisters On thread : my rem 700 3006

    Hey Guys just doing a little thread on my 3006 journey. picked up this rem 700 a couple of years ago it had been floated and pillar bedded and shot real nice I kind of fell in love with the calibre...

    Liked On: 06-12-2021, 09:28 PM

15. 
    SixtyTen liked post by Blisters On thread : my rem 700 3006

    184544

    Liked On: 06-12-2021, 09:28 PM

Page 10 of 22 First 12345678910111213141516171819202122 Last

• Jump to page: