Hey Folks, I have astigmatism in both eyes, plus short sight in left and long sight in right. I recently visited a local optometrist and was not impressed with them at all. Can anyone recommend a...
Liked On: 12-05-2024, 10:06 AM
Looks great, I have modelled similar cuts for a few different actions. Trouble is my mill is manual. How much weight does it save? My tikka T3 action was 476g before I took to it with a mill. I only...
Liked On: 05-05-2024, 05:26 PM
Looks great, I have modelled similar cuts for a few different actions. Trouble is my mill is manual. How much weight does it save? My tikka T3 action was 476g before I took to it with a mill. I only...
Liked On: 05-05-2024, 02:41 PM
Great info, thanks for that. I spent ages looking for something to add some texture to mine, from nonskid grit for boats to truck bed liner. Never though about using this underneath a colored top...
Liked On: 20-04-2024, 03:12 PM
Hello Gents, I recently purchased a 7mm Rem Mag Browning X-Bolt and also bought some once fired Norma brass off Trademe. I found that the cases all had a bad bulge right in front of the belt....
Liked On: 13-04-2024, 09:30 PM
Hello Gents, I recently purchased a 7mm Rem Mag Browning X-Bolt and also bought some once fired Norma brass off Trademe. I found that the cases all had a bad bulge right in front of the belt....
Liked On: 13-04-2024, 06:07 PM
Hey Folks, I thought this could be useful and might interest a few here. I read about this technique on another forum and decided to give it a go. I wanted to make a chamber cast of my No1mk3...
Liked On: 10-03-2024, 03:21 PM
I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....
Liked On: 21-02-2024, 09:06 PM
Yeah, I was limited in size for this one because of the front sight. I'm tossing up putting a red dot or small scope on it as my eyes are not the best. If I did that, I would likely remove the front...
Liked On: 17-02-2024, 02:53 PM
I made a suppressor for this a while back and have not shot it since making it. So I took it along to the range on the weekend to sort out a load for it and see how it shoots with a suppressor. ...
Liked On: 07-02-2024, 10:18 PM
I made a suppressor for this a while back and have not shot it since making it. So I took it along to the range on the weekend to sort out a load for it and see how it shoots with a suppressor. ...
Liked On: 07-02-2024, 08:31 PM
I made a suppressor for this a while back and have not shot it since making it. So I took it along to the range on the weekend to sort out a load for it and see how it shoots with a suppressor. ...
Liked On: 07-02-2024, 10:25 AM
I made a suppressor for this a while back and have not shot it since making it. So I took it along to the range on the weekend to sort out a load for it and see how it shoots with a suppressor. ...
Liked On: 06-02-2024, 09:01 PM
Wow, those look fantastic. Nice work on the checkering, it's not easy and most don't have the patience for it. I have checkered a couple of stocks and it will take a very special project to get me to...
Liked On: 31-01-2024, 01:08 PM
I have a bunch of threaded inserts in the bench top https://www.anzor.co.nz/threaded-inserts/wood-threaded-inserts/m6-304-wood-insert I came up with a 4 bolt pattern (150x75 from memory) and...
Liked On: 01-01-2024, 09:13 AM