SixtyTen
Member

442 Likes

Page 17 of 30 First ... 3456789101112131415161718192021222324252627282930 Last

• Jump to page:

1. 
   40mm liked post by SixtyTen On thread : Ar-15 Dedicated 22lr upper, using CMMG bolt

   Hi everyone, this is a project I recently finished. The plan was to build a dedicated 22lr upper using a standard ar15 upper, a modified CMMG conversion bolt and a used Anschutz 520 barrel. It...

   Liked On: 13-11-2021, 07:05 AM

2. 
   Fssprecision liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

   I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....

   Liked On: 30-10-2021, 06:41 PM

3. 
   Moa Hunter liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

   I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....

   Liked On: 30-10-2021, 08:55 AM

4. 
   gundoc liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

   I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....

   Liked On: 30-10-2021, 05:16 AM

5. 
   257weatherby liked post by SixtyTen On thread : Weatherby becomes a gunsmith!

   Nice job, I quite enjoy diagnosing feed, extraction and ejection problems with rifles. Its often very small things and can be quite challenging. I got a cheap CZ452 .22lr that would not extract fired...

   Liked On: 07-10-2021, 07:52 PM

6. 
   Sideshow liked post by SixtyTen On thread : Weatherby becomes a gunsmith!

   Nice job, I quite enjoy diagnosing feed, extraction and ejection problems with rifles. Its often very small things and can be quite challenging. I got a cheap CZ452 .22lr that would not extract fired...

   Liked On: 07-10-2021, 07:19 PM

7. 
   Fssprecision liked post by SixtyTen On thread : An old one sympathetically bough back

   Awesome, nice job. Id like to see how it shoots. Thanks for posting.

   Liked On: 03-10-2021, 09:56 AM

8. 
   Preacher liked post by SixtyTen On thread : Home ‘bluing’

   I have used duracoat on a few rifles now. Easy enough to apply with a spray gun and seems to be holding up fine. It tool a long time to cure properly completely and stop out-gassing (as in my gunsafe...

   Liked On: 09-09-2021, 02:41 PM

9. 
   Hahn liked post by SixtyTen On thread : Bedding with 10 pounds of upwards pressure on the barrel.

   From what I understand, its mostly used for lighter barrels that are more picky about loads. Putting a pressure point up front will help dampen the barrel a bit and it should shoot better on average...

   Liked On: 07-09-2021, 03:07 PM

10. 
    PaulNZ liked post by SixtyTen On thread : Bedding with 10 pounds of upwards pressure on the barrel.

    From what I understand, its mostly used for lighter barrels that are more picky about loads. Putting a pressure point up front will help dampen the barrel a bit and it should shoot better on average...

    Liked On: 07-09-2021, 03:01 PM

11. 
    Joe_90 liked post by SixtyTen On thread : Howa Mini action - Carbon Stock Project

    Fridge or freezer compressor. One line blows and the other sucks. You can make super quiet low volume air compressors or vacuum pumps from them. Super handy. A vac pump from one of these pulls a...

    Liked On: 05-09-2021, 03:08 PM

12. 
    Tommy liked post by SixtyTen On thread : Howa Mini action - Carbon Stock Project

    Fridge or freezer compressor. One line blows and the other sucks. You can make super quiet low volume air compressors or vacuum pumps from them. Super handy. A vac pump from one of these pulls a...

    Liked On: 05-09-2021, 03:05 PM

13. 
    hunter Al.7mm08 liked post by SixtyTen On thread : Grandfather's .22

    If you have a large gap, solder wont help you much. If you are going to do it yourself, JB weld will work well. Just get everything squeaky clean (degreaser then acetone, and dont touch the...

    Liked On: 04-09-2021, 06:32 PM

14. 
    canross liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

    I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....

    Liked On: 02-09-2021, 01:08 PM

15. 
    Joe_90 liked post by SixtyTen On thread : Howa Mini action - Carbon Stock Project

    A good method for laminating complicated shapes and to keep the carbon weave from getting all messed up is to get some 3m painters plastic, lay that down on a flat table and tape it out so there are...

    Liked On: 01-09-2021, 08:38 PM

Page 17 of 30 First ... 3456789101112131415161718192021222324252627282930 Last

• Jump to page: