SixtyTen
Member

449 Likes

Page 18 of 30 First ... 456789101112131415161718192021222324252627282930 Last

• Jump to page:

1. 
   Hahn liked post by SixtyTen On thread : Bedding with 10 pounds of upwards pressure on the barrel.

   From what I understand, its mostly used for lighter barrels that are more picky about loads. Putting a pressure point up front will help dampen the barrel a bit and it should shoot better on average...

   Liked On: 07-09-2021, 03:07 PM

2. 
   PaulNZ liked post by SixtyTen On thread : Bedding with 10 pounds of upwards pressure on the barrel.

   From what I understand, its mostly used for lighter barrels that are more picky about loads. Putting a pressure point up front will help dampen the barrel a bit and it should shoot better on average...

   Liked On: 07-09-2021, 03:01 PM

3. 
   Joe_90 liked post by SixtyTen On thread : Howa Mini action - Carbon Stock Project

   Fridge or freezer compressor. One line blows and the other sucks. You can make super quiet low volume air compressors or vacuum pumps from them. Super handy. A vac pump from one of these pulls a...

   Liked On: 05-09-2021, 03:08 PM

4. 
   Tommy liked post by SixtyTen On thread : Howa Mini action - Carbon Stock Project

   Fridge or freezer compressor. One line blows and the other sucks. You can make super quiet low volume air compressors or vacuum pumps from them. Super handy. A vac pump from one of these pulls a...

   Liked On: 05-09-2021, 03:05 PM

5. 
   hunter Al.7mm08 liked post by SixtyTen On thread : Grandfather's .22

   If you have a large gap, solder wont help you much. If you are going to do it yourself, JB weld will work well. Just get everything squeaky clean (degreaser then acetone, and dont touch the...

   Liked On: 04-09-2021, 06:32 PM

6. 
   canross liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

   I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....

   Liked On: 02-09-2021, 01:08 PM

7. 
   Joe_90 liked post by SixtyTen On thread : Howa Mini action - Carbon Stock Project

   A good method for laminating complicated shapes and to keep the carbon weave from getting all messed up is to get some 3m painters plastic, lay that down on a flat table and tape it out so there are...

   Liked On: 01-09-2021, 08:38 PM

8. 
   foxhound liked post by SixtyTen On thread : REBARREL REM M700, who would you use?

   I have used Mitch Maxberry in Wellington. He did a very nice job for a very reasonable price and fast turn around time. That was about 4 years ago.

   Liked On: 01-09-2021, 09:36 AM

9. 
   20 Bore liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

   I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....

   Liked On: 28-08-2021, 07:31 PM

10. 
    Micky Duck liked post by SixtyTen On thread : .303 Tank crew carbine

    Damn, Nice work. I have a mid 40s Lithgow with a good barrel that is waiting for the same treatment. However, I am going to do away with the original rear sights and put an aperture on the charging...

    Liked On: 28-08-2021, 12:36 PM

11. 
    PaulNZ liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

    Seeing as I have been stuck at home for the last week, I managed to find some time to work on this rifle. I finished off the sight block and made a aperture holder to screw into it. I am likely...

    Liked On: 27-08-2021, 10:37 PM

12. 
    Micky Duck liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

    I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....

    Liked On: 27-08-2021, 07:12 PM

13. 
    Husky1600 liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

    I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....

    Liked On: 27-08-2021, 07:09 PM

14. 
    Cordite liked post by SixtyTen On thread : .303 Tank crew carbine

    Damn, Nice work. I have a mid 40s Lithgow with a good barrel that is waiting for the same treatment. However, I am going to do away with the original rear sights and put an aperture on the charging...

    Liked On: 27-08-2021, 12:04 PM

15. 
    berg243 liked post by SixtyTen On thread : Suppressing a 45/70

    My 45/70 is 14". If your shooting full house factory loads from a 14" barrel, you will have significant muzzle flash, which means suppressor wear. If you do your own loads to burn completely within...

    Liked On: 25-08-2021, 10:20 PM

Page 18 of 30 First ... 456789101112131415161718192021222324252627282930 Last

• Jump to page: