SixtyTen
Member

442 Likes

Page 26 of 30 First ... 12131415161718192021222324252627282930 Last

• Jump to page:

1. 
   winaa liked post by SixtyTen On thread : Subsonic projectiles, where are we at these days?

   A sneak peak at something im working on at the moment, there will be a full write up on this and the rifle it goes with in the future... Its a 400gr 9mm projectile, sitting in a 308 case cut at...

   Liked On: 19-12-2019, 06:55 AM

2. 
   nowool liked post by SixtyTen On thread : Kiln/Furnace for knife making heat treatment, who built one?

   I made one of these for quickly heat treating small parts that wernt worth starting up my electric furnace for. Super cheap and easy to make. The bricks are the lightweight porous type. Kind of...

   Liked On: 10-10-2019, 02:42 AM

3. 
   veitnamcam liked post by SixtyTen On thread : Drill bits for knife making

   Technically you are completely correct. However, I still have most of my early knives that were heat treated with a short dwell time and they are perfectly serviceable blades. Not as good as my later...

   Liked On: 31-08-2019, 08:24 PM

4. 
   diana2 liked post by SixtyTen On thread : Kiln/Furnace for knife making heat treatment, who built one?

   I made one of these for quickly heat treating small parts that wernt worth starting up my electric furnace for. Super cheap and easy to make. The bricks are the lightweight porous type. Kind of...

   Liked On: 28-08-2019, 09:40 AM

5. 
   diana2 liked post by SixtyTen On thread : Drill bits for knife making

   O1 Tool Steel! Can be bought in very knifemaker friendly sizes (4x40x500, 3x30x500, 3x50x500 etc) It is sold as gauge plate (fully annealed and precision ground) from a few different companies. I...

   Liked On: 26-08-2019, 08:48 PM

6. 
   Glycerine liked post by SixtyTen On thread : Ar-15 Dedicated 22lr upper, using CMMG bolt

   Not a member yet, but im thinking of joining in the near future. I shot some groups with a scope attached and it looked promising considering the muzzle at the time was literally hacksawed...

   Liked On: 09-09-2018, 10:09 PM

7. 
   nance liked post by SixtyTen On thread : Ar-15 Dedicated 22lr upper, using CMMG bolt

   Hi everyone, this is a project I recently finished. The plan was to build a dedicated 22lr upper using a standard ar15 upper, a modified CMMG conversion bolt and a used Anschutz 520 barrel. It...

   Liked On: 02-09-2018, 07:01 PM

8. 
   dogmatix liked post by SixtyTen On thread : Ar-15 Dedicated 22lr upper, using CMMG bolt

   Hi everyone, this is a project I recently finished. The plan was to build a dedicated 22lr upper using a standard ar15 upper, a modified CMMG conversion bolt and a used Anschutz 520 barrel. It...

   Liked On: 02-09-2018, 12:37 PM

9. 
   matto1234 liked post by SixtyTen On thread : Ar-15 Dedicated 22lr upper, using CMMG bolt

   Hi everyone, this is a project I recently finished. The plan was to build a dedicated 22lr upper using a standard ar15 upper, a modified CMMG conversion bolt and a used Anschutz 520 barrel. It...

   Liked On: 02-09-2018, 09:25 AM

10. 
    Glycerine liked post by SixtyTen On thread : Ar-15 Dedicated 22lr upper, using CMMG bolt

    Hi everyone, this is a project I recently finished. The plan was to build a dedicated 22lr upper using a standard ar15 upper, a modified CMMG conversion bolt and a used Anschutz 520 barrel. It...

    Liked On: 02-09-2018, 12:06 AM

11. 
    nzfubz liked post by SixtyTen On thread : Ar-15 Dedicated 22lr upper, using CMMG bolt

    Thanks! A majority of my gunsmithing work is lathe based. The one I bought was about $2000 brand new plus about $1000 in tooling. So it's not completely out of reach for most people to buy one. When...

    Liked On: 01-09-2018, 10:19 PM

12. 
    Beaker liked post by SixtyTen On thread : Ar-15 Dedicated 22lr upper, using CMMG bolt

    Thanks! A majority of my gunsmithing work is lathe based. The one I bought was about $2000 brand new plus about $1000 in tooling. So it's not completely out of reach for most people to buy one. When...

    Liked On: 01-09-2018, 09:07 PM

13. 
    Tommy liked post by SixtyTen On thread : Ar-15 Dedicated 22lr upper, using CMMG bolt

    Thanks! A majority of my gunsmithing work is lathe based. The one I bought was about $2000 brand new plus about $1000 in tooling. So it's not completely out of reach for most people to buy one. When...

    Liked On: 01-09-2018, 08:15 PM

14. 
    TianBotha liked post by SixtyTen On thread : Ar-15 Dedicated 22lr upper, using CMMG bolt

    Thanks! A majority of my gunsmithing work is lathe based. The one I bought was about $2000 brand new plus about $1000 in tooling. So it's not completely out of reach for most people to buy one. When...

    Liked On: 01-09-2018, 07:10 PM

15. 
    muzr257 liked post by SixtyTen On thread : Ar-15 Dedicated 22lr upper, using CMMG bolt

    Hi everyone, this is a project I recently finished. The plan was to build a dedicated 22lr upper using a standard ar15 upper, a modified CMMG conversion bolt and a used Anschutz 520 barrel. It...

    Liked On: 01-09-2018, 02:10 PM

Page 26 of 30 First ... 12131415161718192021222324252627282930 Last

• Jump to page: