steven
Member

1532 Likes

Page 62 of 103 First ... 124849505152535455565758596061626364656667686970717273747576 ... Last

• Jump to page:

1. 
   steven liked post by ebf On thread : Omark improvements

   Shot the Te Puke Champs this weekend. Had a really good shoot, learnt a couple of new tricks :thumbsup: 600yds - got 84/90 for this one (75.09 in TR terms). 30220 Shooting in the rain and...

   Liked On: 24-10-2014, 12:43 PM

2. 
   steven liked post by kiwi39 On thread : 223 reloading

   I've got a Lee collett Neck sizing die I could sell you if you want it What I use : - a forster Bush n Bump Neck Sizing die which also bumps the shoulder (and decaps) ...

   Liked On: 24-10-2014, 12:30 PM

3. 
   steven liked post by Herbmiester On thread : 300blk AR loads

   What ever you sub wise just remember that they are poor killers. My experience is that they pencil through do F all damage and the animal runs off. If you can hit the spine its all good but unless...

   Liked On: 24-10-2014, 10:08 AM

4. 
   steven liked post by Munsey On thread : 223 reloading

   Cheers for that guys , will probably give the reloading a crack as I'm planning on using the 223 a bit more , and probably be more fun than watching tv . What dies should I get ? . Got someone who's...

   Liked On: 24-10-2014, 09:35 AM

5. 
   steven liked post by 6x47 On thread : Anybody bought some of the cheap 223 cases on TM? is it worth bothering with?

   If any case has been -properly- FLd then trimmed and it still sticky in a chamber, it can only be the base that's over-spec. And a small-base die will fix that easily. I'd be very surprised if a...

   Liked On: 24-10-2014, 09:33 AM

6. 
   steven liked post by scaggly On thread : Anybody bought some of the cheap 223 cases on TM? is it worth bothering with?

   I've bought a lot of their RG brass, and it is good. Got one of the hornady chamfer removal tools, and chucked it in the drill. Removal of the crimp only takes a second or so. The brass is thick, so...

   Liked On: 23-10-2014, 01:38 PM

7. 
   steven liked post by res On thread : Anybody bought some of the cheap 223 cases on TM? is it worth bothering with?

   Is this a good time to remind you to put up some photos of your setup?

   Liked On: 23-10-2014, 01:37 PM

8. 
   steven liked post by Beavis On thread : mauser actions

   I thought the lawyer loads were for Krag Jorgesen rifles

   Liked On: 23-10-2014, 01:10 PM

9. 
   steven liked post by Beavis On thread : AR-10 Decisions

   Get a dpms based gun. At least it has some partz commonality. Most mfgs use the dpms gen 1 pattern.

   Liked On: 22-10-2014, 01:43 PM

10. 
    steven liked post by Ryan On thread : AR-10 Decisions

    LoL, just in time to hand down to Sam :P

    Liked On: 22-10-2014, 01:41 PM

11. 
    steven liked post by dogmatix On thread : AR-10 Decisions

    I'm doing the same, have import permits submitted to build up an AR10 from DPMS parts from Brownells. Should be approved in around 8 months. :pissed off:

    Liked On: 22-10-2014, 01:41 PM

12. 
    steven liked post by res On thread : Case for AR15

    While I have proper rifle cases, one of the nice things about AR's is the split in half so easy so I sometimes use a musical case I bought at a op shop for $10 and filled with scrap foam. Cheep as...

    Liked On: 20-10-2014, 11:52 AM

13. 
    steven liked post by Toby On thread : Case for AR15

    Plastic bag :D leave it with me when you head back home too I'll look after it

    Liked On: 20-10-2014, 11:51 AM

14. 
    steven liked post by Spanners On thread : Bullets I make

    DLM wire is a small fortune. I had extrusion dies made in Canada and make my own. https://www.youtube.com/watch?v=gJX0eikISnc

    Liked On: 20-10-2014, 10:34 AM

15. 
    steven liked post by xring On thread : Bullets I make

    You can get lead wire off this company (probably the only one, I think): DLM - Extrusions (http://www.dlm.co.nz/extrusions.html) Tararua, will send you the bullets. Cheers

    Liked On: 20-10-2014, 10:32 AM

Page 62 of 103 First ... 124849505152535455565758596061626364656667686970717273747576 ... Last

• Jump to page: