steven
Member

1532 Likes

Page 14 of 103 First 1234567891011121314151617181920212223242526272864 ... Last

• Jump to page:

1. 
   steven liked post by mikee On thread : How important is die quality?

   Wworkshop Inovations or terminator products could help you

   Liked On: 12-12-2015, 07:19 AM

2. 
   steven liked post by P38 On thread : How important is die quality?

   MDub The only thing rubbish about the Lee RGB or Pacesetter Dies is the advise your local gun shop gave you. :wtfsmilie: I'd also bet the guy that gave you this advise has never even used Lee...

   Liked On: 12-12-2015, 07:05 AM

3. 
   steven liked post by Marty Henry On thread : How important is die quality?

   Ive got rcbs, lee and lyman dies in a variety of calibres the lee dies reload ammo as well as anything imo but their shell holders can be pretty average. You dont need micrometer dies unless you...

   Liked On: 12-12-2015, 07:04 AM

4. 
   steven liked post by Friwi On thread : Suppressors and carbon fouling - what's your got to fix ?

   Hi chainsaw, I think your first mistake is to do all the load development with out the suppressor. Adding the suppressor may have changed your barrel harmonics and opened up your group. I always...

   Liked On: 11-12-2015, 06:30 AM

5. 
   steven liked post by Ryan_Songhurst On thread : Suppressors and carbon fouling - what's your got to fix ?

   I tend to follow the "run a bore snake through it after every hunt and leave it the hell alone other than that" regime, works fine for me, 260 rem cloverleafs/ragged holes still after probably 200+...

   Liked On: 11-12-2015, 06:30 AM

6. 
   steven liked post by res On thread : What happened here?

   As you don't want to use it for safety reasons selling it with full disclosure and a bolt gun only recommendation would seem to be the way to go to me-binning it seems a waste but selling it as...

   Liked On: 08-12-2015, 12:22 PM

7. 
   steven liked post by dogmatix On thread : ADI 62gr .224 Projectiles any good?

   Actually Wayne is doing them for 17.5 cents each if you buy them by the 1000. I use them for SR, as my AR likes heavier projectiles and the Hornady 55gn FMJs and SPs didn't group any better but...

   Liked On: 07-12-2015, 12:26 PM

8. 
   steven liked post by Barefoot On thread : No more Tikka T3s

   That's because they've never been used.

   Liked On: 06-12-2015, 05:38 PM

9. 
   steven liked post by Aoraki Ammo On thread : Aoraki Amunition Company

   We are landing our first container of GECO ammunition next week. https://www.facebook.com/Aoraki-Ammunition-Company-Ltd-861298457268044/?fref=ts :)

   Liked On: 02-12-2015, 07:31 AM

10. 
    steven liked post by Beavis On thread : barnaul 62gr fmj v PMC 55gr FMJ v PMC 77gr SMK

    I have personally found factory .223 ammo to be all over the place. For example I chronied some hornady 75gr steel "match" to find it was dribble slow and had around 150 fps extreme spread. Doesn't...

    Liked On: 01-12-2015, 12:39 PM

11. 
    steven liked post by 338 man On thread : SO, THE SIERRA TMK DO KILL DEER?

    Good work Tahr. Ive just got my AR into the 65gr gamekings but was wondering about the tippd MKs. I would be keen to see bullet damage

    Liked On: 01-12-2015, 07:03 AM

12. 
    steven liked post by Tommy On thread : Mechanical scale wont zero

    Are these two reversed? 42993

    Liked On: 29-11-2015, 08:40 PM

13. 
    steven liked post by shooternz On thread : 303 loads

    Hornady manual lists 38.9 gr max 2206H and 40.8 gr max 2208 COL 2.992" work up from 10% below should be ok, best accuracy is usually 1.5 -2.0 grains below max. Cheers

    Liked On: 26-11-2015, 10:50 AM

14. 
    steven liked post by erniec On thread : Looking at getting into reloading

    I started with a Leeloader the rubber mallet job for a .303 then got a Lee press back in the 80s. Still have the press and I have a Lee loadall in the shed too. They do the job and especially when...

    Liked On: 24-11-2015, 09:25 PM

15. 
    steven liked post by Ryan_Songhurst On thread : Looking at getting into reloading

    I actually LOVE Lee dies, they don't look as flash as some of the other brand but work very well.

    Liked On: 24-11-2015, 06:56 PM

Page 14 of 103 First 1234567891011121314151617181920212223242526272864 ... Last

• Jump to page: