tibo
Member

189 Likes

Page 9 of 13 First 12345678910111213 Last

• Jump to page:

1. 
   Kelton liked post by tibo On thread : 20" Tikka 7 PRC

   Getting good results with 180eldm 66,4gn H4831sc, large rifle primer (fiocchi) and Hornady brass

   Liked On: 31-07-2023, 09:42 PM

2. 
   Moa Hunter liked post by tibo On thread : 7mm PRC Factory Hornady ammo issue

   This is the screenshot from the 7mm PRC group, it is not the one I measured so take it for what it is… I recorded my weight on a A&D Fx300i, I check calibration with calibrated weight before use so...

   Liked On: 06-07-2023, 09:33 AM

3. 
   Micky Duck liked post by tibo On thread : 7mm PRC Factory Hornady ammo issue

   Also started load development, the brass that were ok behaved well. Promising result with H4831sc

   Liked On: 05-07-2023, 07:56 PM

4. 
   Micky Duck liked post by tibo On thread : 7mm PRC Factory Hornady ammo issue

   More on this… shot 2x boxes of new 180 ELDM match (the one with extruded powder not compressed). Not a single issue with this one… 150fps slower average versus precedent batch (around 2830-2850gps on...

   Liked On: 05-07-2023, 07:56 PM

5. 
   gqhoon liked post by tibo On thread : Tikka T3X barrel break-in

   I did notice an important reduction in copper fouling after the first 40 rounds in my new Hardy barrel. I just followed my gunsmith process: 10 passes with Boretech eliminator on a brush (I used a...

   Liked On: 03-07-2023, 10:09 PM

6. 
   Moa Hunter liked post by tibo On thread : Tikka T3X barrel break-in

   I did notice an important reduction in copper fouling after the first 40 rounds in my new Hardy barrel. I just followed my gunsmith process: 10 passes with Boretech eliminator on a brush (I used a...

   Liked On: 03-07-2023, 12:08 PM

7. 
   Micky Duck liked post by tibo On thread : 7mm PRC Factory Hornady ammo issue

   This is the screenshot from the 7mm PRC group, it is not the one I measured so take it for what it is… I recorded my weight on a A&D Fx300i, I check calibration with calibrated weight before use so...

   Liked On: 29-06-2023, 10:29 PM

8. 
   Kelton liked post by tibo On thread : 7mm PRC Factory Hornady ammo issue

   Weighted the brass on the A&D All cases are between 14.643grms and 14.797grms. Can’t find a correlation between weight and “pressure signs”. I can’t be bothered checking volume I will just use the...

   Liked On: 29-06-2023, 10:16 AM

9. 
   Bill999 liked post by tibo On thread : 7mm PRC Factory Hornady ammo issue

   Weighted the brass on the A&D All cases are between 14.643grms and 14.797grms. Can’t find a correlation between weight and “pressure signs”. I can’t be bothered checking volume I will just use the...

   Liked On: 29-06-2023, 10:02 AM

10. 
    Micky Duck liked post by tibo On thread : 7mm PRC Factory Hornady ammo issue

    Weighted the brass on the A&D All cases are between 14.643grms and 14.797grms. Can’t find a correlation between weight and “pressure signs”. I can’t be bothered checking volume I will just use the...

    Liked On: 29-06-2023, 09:56 AM

11. 
    Micky Duck liked post by tibo On thread : 7mm PRC Factory Hornady ammo issue

    Here is another one… boxes I shot had a compressed load, all from same batch. We checked boxes from a newer batch and load is not compressed so less powder or most likely different powder as it...

    Liked On: 28-06-2023, 01:11 PM

12. 
    Micky Duck liked post by tibo On thread : 7mm PRC Factory Hornady ammo issue

    Just a bit of warning regarding Hornady factory 7mm PRC 180 eldm. I had 5 rounds among 60 loaded really hot. Bolt was super hard to lift, bolt face and ejector mark on the case. Primer felt of the...

    Liked On: 28-06-2023, 01:08 PM

13. 
    55six liked post by tibo On thread : Thermal scopes - best bang for your buck?

    Got this little thermal that clip on phone from Ken. Was kind of sceptical but pretty curious about this thing. It is honestly quite good for the price. What I really like about it is you can walk in...

    Liked On: 24-06-2023, 11:23 AM

14. 
    vulcannz liked post by tibo On thread : Thermal scopes - best bang for your buck?

    Got this little thermal that clip on phone from Ken. Was kind of sceptical but pretty curious about this thing. It is honestly quite good for the price. What I really like about it is you can walk in...

    Liked On: 23-06-2023, 09:23 PM

15. 
    mucko liked post by tibo On thread : YouTube star "Rogee" the great New Zealand hunting 'n' shooting ambassador.

    I like his videos. He is showing some good shot and good on him showing the not so good one. Happen to any good hunter once on a while.

    Liked On: 20-06-2023, 12:04 PM

Page 9 of 13 First 12345678910111213 Last

• Jump to page: