Tikka7mm08
Member

1711 Likes

Page 43 of 115 First ... 293031323334353637383940414243444546474849505152535455565793 ... Last

• Jump to page:

1. 
   caberslash liked post by Tikka7mm08 On thread : Hand Primers - What You Using?!

   Got a Sinclair one...great feel on seating. Beautifully made, solid. Not cheap though. https://uploads.tapatalk-cdn.com/20210402/7668caaacb91fd01092f2420d6449846.jpg Sent from my SM-G986B using...

   Liked On: 02-04-2021, 07:29 PM

2. 
   outlander liked post by Tikka7mm08 On thread : Hand Primers - What You Using?!

   Got a Sinclair one...great feel on seating. Beautifully made, solid. Not cheap though. https://uploads.tapatalk-cdn.com/20210402/7668caaacb91fd01092f2420d6449846.jpg Sent from my SM-G986B using...

   Liked On: 02-04-2021, 07:05 PM

3. 
   Micky Duck liked post by Tikka7mm08 On thread : Desirable features of an all round NZ hunting rifle

   Something MSL has spent money on that I buy for half cost. Ideal for me at least.

   Liked On: 30-03-2021, 08:19 PM

4. 
   jakewire liked post by Tikka7mm08 On thread : Beretta differences

   I had an SV10 Prevail and while a beautiful gun it just didn't fit me well and felt slow and heavy. Looked at a 682 Gold E and really liked that but didn't go that way. The 686 felt not as good in my...

   Liked On: 29-03-2021, 06:57 PM

5. 
   Gkp liked post by Tikka7mm08 On thread : Swaro x5i scopes

   The glass on ATACR is some of the best I've had alongside a z6i. I was really surprised.

   Liked On: 28-03-2021, 08:37 AM

6. 
   JessicaChen liked post by Tikka7mm08 On thread : Socks: what do you use

   https://www.stoneglacier.com/products/sg-performance-sock?_pos=1&_sid=2cc3d1d41&_ss=r

   Liked On: 24-03-2021, 07:13 PM

7. 
   veitnamcam liked post by Tikka7mm08 On thread : Suppressor advice sort

   I've had most of them, DPT hard to beat performance, weight, quality and price. Finding A-Tec quite good too.

   Liked On: 24-03-2021, 04:26 PM

8. 
   dannyb liked post by Tikka7mm08 On thread : Suppressor advice sort

   I've had most of them, DPT hard to beat performance, weight, quality and price. Finding A-Tec quite good too.

   Liked On: 24-03-2021, 01:34 PM

9. 
   6.5mm-mag liked post by Tikka7mm08 On thread : 280 Ackley, N560 150gr

   I thought the 7x64 was a ballistic twin for the 280 so a good place to start.

   Liked On: 22-03-2021, 10:27 PM

10. 
    7mmsaum liked post by Tikka7mm08 On thread : New rifle problem

    I had this same problem. Was poor primary extraction and a sloppy extractor.

    Liked On: 22-03-2021, 12:53 PM

11. 
    Mooseman liked post by Tikka7mm08 On thread : New rifle problem

    Ah bingo re the A-bolt. I reload two 280AIs and the Kimber has a tight match chamber. Brass used in the Forbes doesn't like being used in the Kimber. New brass, start from there.

    Liked On: 21-03-2021, 11:18 PM

12. 
    57jl liked post by Tikka7mm08 On thread : Kimber Montana Ascent 280AI Load Development

    Quite cold this morning. Velocity same as the hot weather shot in above. Got the action torqued at 45lbs rear and 50lbs front. Up 10 for rear and 5 for front but not discernible difference. Could...

    Liked On: 21-03-2021, 01:32 AM

13. 
    bumblefoot liked post by Tikka7mm08 On thread : .222 turning back the clock

    I think it was only factory test fired...the bolt face was as new. A minter.

    Liked On: 20-03-2021, 05:25 AM

14. 
    Nathan F liked post by Tikka7mm08 On thread : .222 turning back the clock

    I think it was only factory test fired...the bolt face was as new. A minter.

    Liked On: 19-03-2021, 10:09 PM

15. 
    Stocky liked post by Tikka7mm08 On thread : Kimber Montana Ascent 280AI Load Development

    162gn ELDMs worked up with RE26 and Fed match primers, Norma brass. Mag length. 58, 59 and 60gn loads to test pressure. No issues although the 60gn load blew out the group and the primer strike...

    Liked On: 19-03-2021, 02:36 PM

Page 43 of 115 First ... 293031323334353637383940414243444546474849505152535455565793 ... Last

• Jump to page: