Tikka7mm08
Member

1713 Likes

Page 9 of 115 First 123456789101112131415161718192021222359109 ... Last

• Jump to page:

1. 
   Tikka7mm08 liked post by Woody On thread : Ring/groove at base of case shoulder

   Sorry, I thought the cartidge had the groove. If its the chamber with a recess I would take it to a good gunsmith to make sure it is not a crack and then get his opinion on rechambering if safe. If...

   Liked On: 18-08-2022, 05:07 PM

2. 
   Tikka7mm08 liked post by Gerardo On thread : Kimber Montana 308 Load Development

   Can't complain about that grouping mate! Excellent Sent from my SM-G975F using Tapatalk

   Liked On: 15-08-2022, 09:02 AM

3. 
   Tikka7mm08 liked post by Bobba On thread : Pull throughs

   I think bore snakes with oil are a terrible idea as it's just going to get filthy then your dragging the same crap thorough you barrel everytime. You need to use patches that get thrown away after it...

   Liked On: 14-08-2022, 07:19 PM

4. 
   Tikka7mm08 liked post by deer4u On thread : Kimber Montana 308 Load Development

   photo

   Liked On: 14-08-2022, 02:26 PM

5. 
   Tikka7mm08 liked post by veitnamcam On thread : 6.5 PRC Load Development Begins

   Because you effectively have a bigger case if it's not half full of projectile. Not going to be as noticable in something with a large case capacity.

   Liked On: 11-08-2022, 10:46 PM

6. 
   Tikka7mm08 liked post by Tahr On thread : 6.5 PRC Load Development Begins

   Looks good. You could stop any time now and go hunting (I just wanted to be aead of Nathan to say that).

   Liked On: 11-08-2022, 10:26 PM

7. 
   Tikka7mm08 liked post by dannyb On thread : 6.5 PRC Load Development Begins

   Not in my experience :thumbsup:

   Liked On: 11-08-2022, 09:42 PM

8. 
   Tikka7mm08 liked post by flock On thread : Ultrasonic cleaner tips please

   Real Lazy these days, and most of my shooting is at paper, still getting good results. Always give the inside necks a clean wire bore brush & battery drill, dirty outside necks get a quick polish...

   Liked On: 06-08-2022, 01:13 AM

9. 
   Tikka7mm08 liked post by dannyb On thread : Tikka Veil Factory Stock Weight

   Bob has short arms too :yaeh am not durnk: well compared to me anyway :D

   Liked On: 06-08-2022, 01:12 AM

10. 
    Tikka7mm08 liked post by No.3 On thread : Ultrasonic cleaner tips please

    The propriety stuff sold as ultrasonic cleaner fluid in the US is basically just showerpower bam. Spray bottle at the supermarket... It's a citric acid and natural plant based stuff that's pretty...

    Liked On: 05-08-2022, 12:00 AM

11. 
    Tikka7mm08 liked post by Gerardo On thread : Kimber Montana 308 Load Development

    You're on form there mate! Sent from my SM-G975F using Tapatalk

    Liked On: 04-08-2022, 08:11 PM

12. 
    Tikka7mm08 liked post by Cyclops On thread : Ultrasonic cleaner tips please

    The steps I folllow Deprime inspect cases Anneal - every 5th use Full length size Ultrasonic clean oven dry at low heat (120 C), air cool on clean towel inspect cases prime, load with...

    Liked On: 04-08-2022, 01:11 PM

13. 
    Tikka7mm08 liked post by shift14 On thread : 6.5 PRC Load Development Begins

    Really enjoying this thread…. 202958 B

    Liked On: 04-08-2022, 12:55 AM

14. 
    Tikka7mm08 liked post by Magnus On thread : Ultrasonic cleaner tips please

    I've got the Lyman one and have been using the hornady cleaner that I got given with it. With the Lyman one the basket sits on the bottom of the cleaner basin and seems to stop the high frequency...

    Liked On: 03-08-2022, 07:16 PM

15. 
    Tikka7mm08 liked post by nor-west On thread : MS_SP Magnetospeed chronograph

    Not worried about poi change, will get an accurate load(s) then chrono it.

    Liked On: 03-08-2022, 02:14 PM

Page 9 of 115 First 123456789101112131415161718192021222359109 ... Last

• Jump to page: