winaa
Member

336 Likes

Page 13 of 23 First 1234567891011121314151617181920212223 Last

• Jump to page:

1. 
   winaa liked post by Tikka7mm08 On thread : Powder suggestions 7mm08 120nbt

   I dropped from 140gn ABs and BTs to 120gn BTs. I kept the same load...50gn 2209 and CCI mag primer. Stupid accurate in Tikkas and Rem Mod 7.

   Liked On: 16-03-2020, 06:19 AM

2. 
   winaa liked post by ebf On thread : 708 questions

   Very happy with it. The 162 ELD-M is pretty much the same projectile. Did not have to make any changes to my loads between the AMAX and ELMD, and I would confidently shoot both of those at animals,...

   Liked On: 09-03-2020, 03:33 PM

3. 
   winaa liked post by Micky Duck On thread : 25-06 why hasn't it achieved fame and success in New Zealand?

   so for you melenials.......and anyone else still following this thread....... the point n shoot thing mentioned above was THE VERY REASON the likes of the poohseventy /EBRG and the likes got such a...

   Liked On: 09-03-2020, 10:40 AM

4. 
   winaa liked post by 7mmsaum On thread : 708 questions

   #stopfuckinshorteningriflebarrels

   Liked On: 09-03-2020, 10:36 AM

5. 
   winaa liked post by joelhenton On thread : 708 questions

   16" barrel I'm running Hornady ELD-M 162gr at 2600 fps. Stopped when my groups tightened up.

   Liked On: 09-03-2020, 09:01 AM

6. 
   winaa liked post by ishoot10s On thread : 300BLK questions

   My pet load was 10 grains of AR2207 behind the 240 grain SMK. Just over 1000 FPS in the, now crushed, AR.

   Liked On: 05-03-2020, 07:01 AM

7. 
   winaa liked post by rambo-6mmrem On thread : Shimming scope...

   Personally id but a set of burris zrings with a +.020 insert in the rear and a -0.20in the front But those are almost half the cost of a jw15 So a peice of coke can in the rear ring will have to do

   Liked On: 28-02-2020, 07:01 PM

8. 
   winaa liked post by Howa270 On thread : Camo tape on suppressor

   Im sure its a placebo type thing but I swear mines quieter with tape on it. I got a few rolls off aliexpress for $2 each and its exactly the same as the stuff H&F sells for $25. Message me your...

   Liked On: 26-02-2020, 08:46 PM

9. 
   winaa liked post by Flyblown On thread : 18 inch 308 powder

   Think of it in terms of percentages. How much, in percentage terms, am I going to gain if I change powder? I guarantee you it will be less than 5%. That isn’t worth it mate, the ballistics will...

   Liked On: 24-02-2020, 08:33 PM

10. 
    winaa liked post by cameronjackwhite On thread : . 284 Winchester

    .318 neck eliminated the donut issue from necking up 6.5x284 I believe. Pretty sure GWH knows more on the subject

    Liked On: 20-02-2020, 08:55 PM

11. 
    winaa liked post by Rock river arms hunter On thread : . 284 Winchester

    160gr TMKs at 2830fps out of my 284. As I own a 308 already I could never justify a 7-08. However out of interest both 308 and 284 are similar weight, same recoil pad, same length barrel etc. ...

    Liked On: 18-02-2020, 07:52 PM

12. 
    winaa liked post by superdiver On thread : . 284 Winchester

    I loved my 284, definitely a cool calibre as SS says but when I did load development for a mates 18" 708 and got it shooting the 162eldx at 2660 shooting sub moa using less than 40grs of powder it...

    Liked On: 09-02-2020, 03:09 PM

13. 
    winaa liked post by wsm junkie On thread : . 284 Winchester

    There must be something to these tikka 9.5 twist barrels. This is the results of my dabble with the 180 eldm's in my 7mm08ai Load development 129941 And a group at 600yds with the chosen...

    Liked On: 06-02-2020, 01:26 PM

14. 
    winaa liked post by GWH On thread : . 284 Winchester

    I've got a couple of 284 wins. Both rechambered tikka 708s. One is a T3 cut to 17" with DPT magnum suppressor. Long mag and bolt stop. The barrel was throated long to suit 162s seated out in...

    Liked On: 05-02-2020, 03:44 PM

15. 
    winaa liked post by JaSa On thread : Pulling projectile - neck tension?

    Hi everyone, Thank you very much for all your replies ! Plinky kindly offered to pull the projectiles for me and I will resize the cases without the de-primer rod in afterwards just to make sure...

    Liked On: 04-02-2020, 08:45 PM

Page 13 of 23 First 1234567891011121314151617181920212223 Last

• Jump to page: