winaa
Member

336 Likes

Page 1 of 23 123456789101112131415 ... Last

• Jump to page:

1. 
   winaa liked post by shooternz On thread : Pistol powders in rifles question

   Ap70n is ADI's version of Unique it is sold in the US as Universal standard cast bullet start load is 10 grains in .30 cal rifles with a 180-200 grain bullet, should not need a filler if the...

   Liked On: 07-07-2022, 10:14 PM

2. 
   winaa liked post by shooternz On thread : LEE LEAD MELTER ADVICE

   Start with 1 stick to 10 kg of lead is usually enough you only need enough to fill out the mould Tin is not for hardness, For hunting bullets the softer the better, High velocity with cast is...

   Liked On: 14-06-2022, 10:51 PM

3. 
   winaa liked post by Flyblown On thread : hornady's new CX bullet

   No, I wouldn’t agree with that. From the testing done by fellas in the US, the GMX and CX are performing very differently. The CX looks like it is considerably softer than the GMX and will break...

   Liked On: 09-06-2022, 11:13 AM

4. 
   winaa liked post by shooternz On thread : Magnum primers with Trailboss ?

   Don't worry about the primers you are working at the bottom of the load density range, In a .308 most use 8.0 grains of Trail Boss for about 1040 fps so you have plenty of spread left in the...

   Liked On: 07-06-2022, 11:10 AM

5. 
   winaa liked post by Flyblown On thread : hornady's new CX bullet

   misser I’m assuming you’re in Michigan… this is probably a longshot but is there any way that you can demonstrate the expansion on these new Hornady bullets? Maybe shoot some milk jugs full of...

   Liked On: 24-05-2022, 01:09 PM

6. 
   winaa liked post by Cordite On thread : annealing help please

   It seems you are talking about annealing in order to avoid overworking your brass, to get more reloads per case. Here the main considerations are to heat sufficiently to anneal the neck/shoulder,...

   Liked On: 16-05-2022, 08:02 AM

7. 
   winaa liked post by Bill999 On thread : Loading 7.62x39 subsonic from steel cased factory ammo

   everything Iv shot with it so far has been a very convincing kill Im careful with shot placement but I have zero complaints with it strangely it hits harder and kills better than a 44mag at...

   Liked On: 27-04-2022, 08:47 PM

8. 
   winaa liked post by Pommy On thread : Loading 7.62x39 subsonic from steel cased factory ammo

   I've also been impressed with the SubX so far. Here's one recovered after passing through a wallaby's chest and burying in the dirt. 195597 And here's a headshot. Small entry between the eyes....

   Liked On: 27-04-2022, 08:47 PM

9. 
   winaa liked post by Bill999 On thread : Loading 7.62x39 subsonic from steel cased factory ammo

   in my 300blk im using 190 subx I have a cast 151 load Iv built up for both my 308 and 300blk that I use interchangeably I still have a fair few boxes of subx and I used up all my loaded cast ones...

   Liked On: 27-04-2022, 08:46 PM

10. 
    winaa liked post by Bill999 On thread : Loading 7.62x39 subsonic from steel cased factory ammo

    I use 30cal subs for everything these days, in 300blk It works well on everthing from turkeys to home kill bulls shots need to sever the spine(hard) or scramble the brain(less hard) I site for...

    Liked On: 22-04-2022, 08:15 AM

11. 
    winaa liked post by Hahn On thread : Magnetospeed sporter on a suppressor

    Ha no iron content in the projectiles... Which means I don't understand how the magnetospeed works :cave: I got my 10x2.5mm at https://amfmagnets.co.nz/ in Aus The manual says you need a 1/8"...

    Liked On: 19-04-2022, 08:59 AM

12. 
    winaa liked post by LMcNab On thread : Simple removable reloading press setup.

    Just finished my setup today. Components are in the draws, press and powder thrower can be stored out of the way in about 5 seconds. https://youtube.com/shorts/EbVSmMPv-UU?feature=share

    Liked On: 20-02-2022, 05:07 PM

13. 
    winaa liked post by shooternz On thread : 338 Federal versus 358 Winchester

    How about this one 82231 No gas check but ideal for subs

    Liked On: 16-02-2022, 03:54 PM

14. 
    winaa liked post by shooternz On thread : .277 bullet mold

    Not a good idea the 270 is not really suitable for cast bullet there are few mold s available, the case capacity is way too large the barrel twist is too fast velocity is limited to 1500-1800fps, No...

    Liked On: 15-02-2022, 02:07 PM

15. 
    winaa liked post by shooternz On thread : Who Is Using 350 Legend ?

    I know you are after a 350 Legend but Winchester dropped the ball with it unless you are an AR15 user, Have you thought about a .358 Winchester better selection of bullet weights, I do cast .358's...

    Liked On: 15-02-2022, 12:36 PM

Page 1 of 23 123456789101112131415 ... Last

• Jump to page: