xtightg
Banned

1529 Likes

Page 9 of 102 First 123456789101112131415161718192021222359 ... Last

• Jump to page:

1. 
   xtightg liked post by Sarvo On thread : Photos of your dog

   It was the Russians that did it :thumbsup:

   Liked On: 28-02-2020, 06:26 PM

2. 
   xtightg liked post by rambo-6mmrem On thread : Shimming scope...

   Personally id but a set of burris zrings with a +.020 insert in the rear and a -0.20in the front But those are almost half the cost of a jw15 So a peice of coke can in the rear ring will have to do

   Liked On: 28-02-2020, 06:12 PM

3. 
   xtightg liked post by gimp On thread : 25-06 why hasn't it achieved fame and success in New Zealand?

   That's my effortpost for the week. Any subsequent responses will be sarcastic in nature.

   Liked On: 27-02-2020, 04:07 PM

4. 
   xtightg liked post by Nugget connaisseur On thread : Photos of your dog

   Everyone comments on her ears. Is she X with a Dingo? or something. When she was a pup 1 ear was up one was down. It was the Best! 131561 131562 131563

   Liked On: 27-02-2020, 01:51 PM

5. 
   xtightg liked post by Flyblown On thread : Photos of your dog

   Shitty photo I know but something very strange has happened in this Waikato drought. Both my Staffords now spend all night out on the driveway eating insects that come to the garage lights. I cannot...

   Liked On: 26-02-2020, 10:07 PM

6. 
   xtightg liked post by Steve123 On thread : General, bush and long range

   See if you can find a Ruger Scout. 308, 16 inch barrel, 10,5 and 3 shot mags available. If you get the blued ones they come with a 5/8x24 threaded flash hider,

   Liked On: 26-02-2020, 09:53 PM

7. 
   xtightg liked post by savage270 On thread : Mahitahi River Tahr block

   Il come n show you around

   Liked On: 26-02-2020, 08:53 PM

8. 
   xtightg liked post by Robojaz On thread : DIY Carbon Fiber Rifle Stock

   FIRST GO AT A FIBERGLASS STOCK With the mold complete it was now time to bite the bullet and have a go at making my first rifle stock. As I previously mentioned I had decided that I would make my...

   Liked On: 26-02-2020, 08:51 PM

9. 
   xtightg liked post by davetapson On thread : Engineering shop to mill Stock extensions

   Routed a spacer out of 25mm Acrylic (I think). Feels really good in terms of LOP, but heavy and slightly unbalances rifle. Will drill holes through the centre to remove weight, and (possibly)...

   Liked On: 26-02-2020, 12:53 PM

10. 
    xtightg liked post by Bill999 On thread : Engineering shop to mill Stock extensions

    4cm is a lot, are you very tall? The cheep option is thick plastic cut with a jigsaw then sanded You can use anything from a chopping board or 20l containers or anything that's accessible to you

    Liked On: 26-02-2020, 12:53 PM

11. 
    xtightg liked post by gundoc On thread : Shimming scope...

    Shimming the rear ring is OK and will not cause problems. You can cut shims from aluminium drink cans with a pair of scissors. The shim only needs to be at the bottom, about15mm is long enough.

    Liked On: 26-02-2020, 12:13 PM

12. 
    xtightg liked post by grandpamac On thread : Grandpamac Discovers a Bog

    131489 Greetings All, Went for a short walk to the Kuripapango Lakes today, looking for a few spots an old fudd could have a little hunt now that the temperature has dropped a little. The lakes...

    Liked On: 25-02-2020, 10:27 PM

13. 
    xtightg liked post by Robojaz On thread : DIY Carbon Fiber Rifle Stock

    MAKING THE MOLD Up until this stage I was fairly comfortable with what I had to do and how to proceed, from here I was in unfamiliar territory. Consequently, I sought advice and received some very...

    Liked On: 25-02-2020, 05:32 PM

14. 
    xtightg liked post by Nugget connaisseur On thread : 308 165gr

    I havnt tried the nosler BTs but the red box is usually around half the price or just over as Nosler are 50 projectile boxes not 100. Probably why most people try the SSTs first and they seem to...

    Liked On: 25-02-2020, 03:07 PM

15. 
    xtightg liked post by Cigar On thread : 243 powders

    I use ADI powders because they are easy to get. In the 243 I use AR2209 because it seemed to be the most recommended. I use 2208 in other calibres and could have used that instead.

    Liked On: 24-02-2020, 09:33 PM

Page 9 of 102 First 123456789101112131415161718192021222359 ... Last

• Jump to page: