zeropak
Member

524 Likes

Page 24 of 35 First ... 1011121314151617181920212223242526272829303132333435 Last

• Jump to page:

1. 
   Oldbloke liked post by zeropak On thread : Pressure signs with factory ammo

   Brand new rifle so carbon/copper buildup will not be the issue. Not the ammo because the milder Fiocchi was giving the same pressure signs. Good point regarding the edges of the ejector holes but the...

   Liked On: 05-03-2023, 10:56 AM

2. 
   veitnamcam liked post by zeropak On thread : Pressure signs with factory ammo

   Brand new rifle so carbon/copper buildup will not be the issue. Not the ammo because the milder Fiocchi was giving the same pressure signs. Good point regarding the edges of the ejector holes but the...

   Liked On: 05-03-2023, 09:02 AM

3. 
   PipIstrelle liked post by zeropak On thread : Pressure signs with factory ammo

   Brand new rifle so carbon/copper buildup will not be the issue. Not the ammo because the milder Fiocchi was giving the same pressure signs. Good point regarding the edges of the ejector holes but the...

   Liked On: 04-03-2023, 09:43 PM

4. 
   Tahr liked post by zeropak On thread : Pressure signs with factory ammo

   Oh Ok. I think there is more going on than that. Considering the hard tight to lift bolt and shots going wide of the group.

   Liked On: 04-03-2023, 05:05 PM

5. 
   chainsaw liked post by zeropak On thread : Suppressor rear bush sizing

   Yep I get that. solid consistent contact or no contact at all should work. But partial or variable contact would most likely cause accuracy issues.

   Liked On: 28-02-2023, 08:28 AM

6. 
   veitnamcam liked post by zeropak On thread : Suppressor rear bush sizing

   Yep I get that. solid consistent contact or no contact at all should work. But partial or variable contact would most likely cause accuracy issues.

   Liked On: 28-02-2023, 07:36 AM

7. 
   Fssprecision liked post by zeropak On thread : Suppressor rear bush sizing

   Yep I get that. solid consistent contact or no contact at all should work. But partial or variable contact would most likely cause accuracy issues.

   Liked On: 27-02-2023, 09:42 PM

8. 
   Rated M for Magnum liked post by zeropak On thread : 6.5 143 ELD-X, are they THE 6.5 hunting bullet?

   The 143gn ELDX looks like THE Projectile for the 6.5 calibre. I shoot a 6.5 Creedmoor and use factory ammo. I have been mainly using the Hornady superformance 129gn SST. I recently bought a couple...

   Liked On: 13-02-2023, 02:14 AM

9. 
   MB liked post by zeropak On thread : Lesson Learnt - Cheap Rings

   Find yourself a set of medium height Talley rings. medium will give enough clearance for the 50mm objective. Ring and base all one piece, very simple design and they work. About $115 for a set so...

   Liked On: 14-01-2023, 11:28 PM

10. 
    Micky Duck liked post by zeropak On thread : shooting sticks

    Yes it does. Squeeze the trigger on the trigger stick and the legs will extend to where they hit ground. So each leg can go to different extension length. Uneven ground is no problem.

    Liked On: 14-01-2023, 11:22 PM

11. 
    lau lau liked post by zeropak On thread : Lesson Learnt - Cheap Rings

    Find yourself a set of medium height Talley rings. medium will give enough clearance for the 50mm objective. Ring and base all one piece, very simple design and they work. About $115 for a set so...

    Liked On: 14-01-2023, 09:21 PM

12. 
    dannyb liked post by zeropak On thread : Lesson Learnt - Cheap Rings

    Find yourself a set of medium height Talley rings. medium will give enough clearance for the 50mm objective. Ring and base all one piece, very simple design and they work. About $115 for a set so...

    Liked On: 14-01-2023, 08:01 PM

13. 
    6.5 CRD liked post by zeropak On thread : Lesson Learnt - Cheap Rings

    Find yourself a set of medium height Talley rings. medium will give enough clearance for the 50mm objective. Ring and base all one piece, very simple design and they work. About $115 for a set so...

    Liked On: 14-01-2023, 05:13 PM

14. 
    kruza liked post by zeropak On thread : Chronograph advice

    Yep I get what your saying and even with a Chronograph it would be a good idea to validate the data on a target. I do that now but I guess I like to tinker and I would love to know the actual MV of...

    Liked On: 08-01-2023, 05:26 PM

15. 
    Moa Hunter liked post by zeropak On thread : Time for a scope upgrade?

    There are some good ballistic programs out there to help you. Swarovski has an excellent one on their website for use with their scopes. Another option (which I am now using) is Strelok Pro which is...

    Liked On: 15-12-2022, 08:38 AM

Page 24 of 35 First ... 1011121314151617181920212223242526272829303132333435 Last

• Jump to page: