zimmer
Member

1490 Likes

Page 54 of 100 First ... 44041424344454647484950515253545556575859606162636465666768 ... Last

• Jump to page:

1. 
   zimmer liked post by gundoc On thread : L2A2?

   L2A2 was the correct military designation for the standardised 7.62x51 ball cartridge as manufactured by CAC. Some over-run cases from when CAC lost the military contract in 1965 were used to load...

   Liked On: 27-08-2021, 03:43 PM

2. 
   zimmer liked post by HJA8 On thread : The Precision rimfire thread

   I've got a Vudoo V22 repeater and a 360 repeater in transit - Not sure when I'll set eyes on it with all these lock downs! Here's 150 shots at 50 yesterday in the wind - four lots of ammo - two...

   Liked On: 27-08-2021, 12:36 PM

3. 
   zimmer liked post by jeremyc On thread : printable targets

   hey guys. new shooter here. I've not been doing it very long and i have had trouble finding decent targets with 1" increments. most of the ones i find say they are but are always just over half inch....

   Liked On: 26-08-2021, 04:15 PM

4. 
   zimmer liked post by grandpamac On thread : Working up a Load in a Components Drought.

   Greetings All, Working up a load for your rifle can be as easy or as difficult as you want it to be. I have noted quite a few posts lately describing extensive load development techniques that...

   Liked On: 25-08-2021, 06:08 PM

5. 
   zimmer liked post by Flyblown On thread : CCI Standard Velocity problems

   Not useless at all @zimmer (https://www.nzhuntingandshooting.co.nz/member.php?u=1214), gave me something to go on. I have been having ongoing problems with the subsonic crack, and a high POI. ...

   Liked On: 24-08-2021, 03:58 PM

6. 
   zimmer liked post by 7mm Rem Mag On thread : electronic scales

   I paid $1275 for the fx 300i bare scale. Since Im only reloading to hunt I can trickle the load by hand however that V3 system looks great if doing a lot of target shooting

   Liked On: 24-08-2021, 01:31 PM

7. 
   zimmer liked post by janleroux On thread : electronic scales

   I have moved from using manual (Lee) and stand-alone (Hornady) scales to an Intellidropper. Before I struggled to get and keep my ES down, but now I am within single digits on Hornady brass. It...

   Liked On: 24-08-2021, 12:42 PM

8. 
   zimmer liked post by Pommy On thread : Powder supply

   Yes, have a chat with your nearest shop and put yourself down for whatever bits you require. Be prepared to wait or settle for for alternatives. Prices are going up. Now's not a bad time to own a 270...

   Liked On: 23-08-2021, 04:47 PM

9. 
   zimmer liked post by gqhoon On thread : Primer seating depth problems with new Lapua brass ?

   Lapua SRP primer pockets are about .003 deeper than standard (0.122 versus 0.125). You must be crushing your primer anvils a fair bit, normally would set them 0.002-0.006 below case head.

   Liked On: 22-08-2021, 07:26 PM

10. 
    zimmer liked post by Micky Duck On thread : show us your chainsaws

    and finally my family175831175832

    Liked On: 22-08-2021, 03:55 PM

11. 
    zimmer liked post by Micky Duck On thread : show us your chainsaws

    used a similar set up with two 066 STIHLS on end of 6 foot bar...Roger Larsen from Ratehi owned it and we used to slab rimu in bush and get flitches at 750kgs then fly out under a jetranger...was fun...

    Liked On: 22-08-2021, 02:29 PM

12. 
    zimmer liked post by 2post On thread : nzhs rimfire challenge

    I’m keen to see what I can do with my old slazenger single shot with broken rear sight when I can get to a range. I’ve never tried a target but can reliably hit bunnies between the eyes. If I’m no...

    Liked On: 22-08-2021, 01:35 PM

13. 
    zimmer liked post by BSA On thread : Thoughts on BSA CF2 270?

    All of the BSA's are good rifles but in true pommy tradition they started with the best Hunter/Regents/Majestics then went backwards to Monarch and finally the CF2. That is my opinion only but I own...

    Liked On: 22-08-2021, 11:51 AM

14. 
    zimmer liked post by dogmatix On thread : Resurgence of interest in the old "Three Oh"?

    My 42 Longbranch No4Mk1* is 2 groove. Shoots stupidly accurately. Here's my 1917 III* sporter mentioned earlier in the thread.. 175678

    Liked On: 21-08-2021, 04:44 PM

15. 
    zimmer liked post by gundoc On thread : threading odd muzzle

    It can be internally threaded and an adapter made but it must be done on a lathe with a 4-jaw chuck and clocked true with the bore using a neat fitting spud. Any proper gunsmith should whack it out...

    Liked On: 20-08-2021, 07:35 PM

Page 54 of 100 First ... 44041424344454647484950515253545556575859606162636465666768 ... Last

• Jump to page: