Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

DPT Alpine


User Tag List

+ Reply to Thread
Results 1 to 5 of 5
  1. #1
    Member Sasquatch's Avatar
    Join Date
    Nov 2014
    Location
    The Forest
    Posts
    1,642

    Service Rifle question

    Does anyone know if this rifle qualifies for NZSRA service class?

    http://www.nzhuntingandshooting.co.n...15-acat-34523/

    Does the barrel need to have the cuts for the grenade launcher (govt profile) or can it be standard straight barrel?

    Cheers
    Sas

  2. #2
    Member 300CALMAN's Avatar
    Join Date
    Dec 2014
    Location
    NZISTAN
    Posts
    3,592
    No it should be fine in general however the "A Cat" stock is not standard and the muzzle break isn't either. You could e-cat it and change to a normal A3 and compensator.

  3. #3
    Member Tommy's Avatar
    Join Date
    Nov 2014
    Location
    W-BOP
    Posts
    5,256
    New Zealand Service Rifle Association - Service Match Code

    9.3.3.1 AR15
    Note: “standard” refers to features and or
    parts identical (fire control components to
    be NZ legal for an MSSA) to those that
    make up such rifles as the military issue
    Bushmaster shown. Any acceptable variation
    from the “standard” is detailed below.
    Upper Receiver:A1, A2 or Flat Top A3/A4.
    No Match style, high rise, or similar receivers allowed. Milspec standard A1/A2 style
    charging handles only.
    Lower Receiver: A1/A2 style with standard Milspec controls. No extended magazine, bolt
    or safety levers. A left handed safety may be fitted if it is the same type as a right handed
    safety. Magazine wells may not be modified.
    Barrel: Chamber is to be 5.56 NATO, SAAMI STD .223 Remington or a chamber that
    will feed all Mil-spec ammo.
    Barrel diameter is based on A1, A2, or A2 HBAR and must have an A1 or A2 fixed
    front sight block that is pinned to the barrel. Twist rates from 1/7 to 1/12 are
    acceptable.
    Barrels must be chrome-moly or chrome lined, no stainless barrels allowed.
    Maximum Dimensions: Maximum length is 20 inches.
    Barrel diameter under the hand-guards (Not including the chamber area) must not
    exceed .96 of an inch up to the gas-block where it must drop to the standard .750
    diameter so as to fit a standard A2 gas block. The barrel diameter forward of the
    front sight must not exceed .740 of an inch.
    Carbine barrels; can be either 14.5 or 16” and can be M4, M4A1 or HBAR profile with
    a fixed (pinned) A1 or A2 gas block. Otherwise specifications are the same as for 20
    inch barrels.
    The following picture shows typical maximum dimensions for HBAR style barrels. Note
    that several manufacturers have a slightly larger section over the chamber of .98”.
    Stocks: A1, A2 and CAR/M4 butt stocks are acceptable. Hand guards may be A1, A2 or
    Knights Armament RAS style fore ends or similar type. Free floating of the barrel is not
    permitted.
    Pistol grips: are to be A1 or A2. Hogue and other accessory pistol grips are not allowed.
    Knights style front grips are permitted
    Trigger: Milspec standard A1/A2 style with a single stage release; no match single or 2
    stage triggers may be fitted. Pull weight for a standard AR15 trigger is a minimum 5.5
    pounds. No aftermarket spring kits or lightened components allowed
    Magazine: Any capacity up to 30 rounds. Magazine must not be modified to allow hand
    loaded ammunition to be seated further out. New style anti tilt followers and Magpul bases
    are acceptable. Magazine couplers and after market floor plates are permitted
    Identify your target beyond all doubt

  4. #4
    Member Sasquatch's Avatar
    Join Date
    Nov 2014
    Location
    The Forest
    Posts
    1,642
    Awesome thanks guys, I would ditch the AIL stock and put an A2 buttstock on & lose the muzzle break for a standard A2 birdcage. Just wasn't sure about the barrel, for some reason can't download pdf's atm on my phone for the SR match code.

  5. #5
    Member dogmatix's Avatar
    Join Date
    Dec 2011
    Location
    Northern Gaul (Pukekohe)
    Posts
    3,720
    Nothing wrong with Stag either.
    Welcome to Sako club.

 

 

Similar Threads

  1. Service rifle 3x or 4x
    By Greenie in forum Firearms, Optics and Accessories
    Replies: 19
    Last Post: 19-02-2016, 03:35 PM
  2. Replies: 2
    Last Post: 04-09-2015, 07:47 PM
  3. Replies: 5
    Last Post: 30-12-2014, 01:01 PM
  4. Replies: 6
    Last Post: 27-10-2014, 03:40 PM
  5. Bruce Rifle Club Service Rifle Competition 2013
    By fernleaf in forum Shooting
    Replies: 11
    Last Post: 28-10-2013, 07:38 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!