Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

Darkness Delta


User Tag List

+ Reply to Thread
Results 1 to 7 of 7
  1. #1
    Member smidey's Avatar
    Join Date
    Nov 2013
    Location
    Whangarei Heads
    Posts
    1,157

    Norinco Trigger adjustment

    So my JW105 (223) is teaching me heaps which is the point of the cheap gun.

    I have floated the barrel and put a few rounds through it to get it some where near sighted in.

    My question is, should i mess around with the trigger adjustment or leave something like that to a pro? I have the instruction manual showing me what screw does what, it has what i would call a 4 way adjustment.

    What's the worst that could happen?
    If i could have a full time job shooting pests i'm up for over time.

  2. #2
    Village Idjit Barefoot's Avatar
    Join Date
    Dec 2011
    Location
    Bunji's Bach
    Posts
    3,896
    They aren't hard to adjust. If you adjust the creep and weight too much the safety stops working though and if you slam the but down it will fire it.
    So just do the adjustments a small bit at a time and you will be fine.

  3. #3
    Member smidey's Avatar
    Join Date
    Nov 2013
    Location
    Whangarei Heads
    Posts
    1,157
    thanks very much barefoot, i'll do some more learning haha
    If i could have a full time job shooting pests i'm up for over time.

  4. #4
    Member
    Join Date
    Feb 2012
    Location
    in the middle of the bottom of the south
    Posts
    427
    Take note of where the settings are, and ajust each thing 1 at a time, then check fu tion still works.
    I like to first ajust the pull weight, then sear engagement, then over travel.
    Screw out the pull weight screw to, say, 2.5lb.
    Then I cock the action and screw in the sear engagement screw untill it drops the firing pin. Then screw it back out about a quarter turn.
    then screw the overtravel in until it stops the trigger firing, then back out about a quarter turn. Check for safe funtion and slam the shit out of the bolt to see it will not decock itself on closing.
    It should be all good.
    greg
    Sometimes you will need to back the sear engagement off a little to keep the safety working.

  5. #5
    Member
    Join Date
    May 2012
    Location
    Far North
    Posts
    4,812
    if it has springs inside then swap them out rather than cutting them, pens are a good donor for trigger springs

    Just be very sure of what your doing before you do something that can not be easily undone

    also youtube it and sit watch and learn

  6. #6
    Member Haggie's Avatar
    Join Date
    Jan 2013
    Location
    Auckland/Otago
    Posts
    258
    Good way to check you havent lightened it up too much is just be really rough with the bolt on closing and give the butt a bang with a rubber mallet, if it doesnt fire that way and you like the trigger pull your sorted and wont slip over in the bush and give yourself a lead injection.

  7. #7
    Member
    Join Date
    May 2012
    Location
    Far North
    Posts
    4,812
    and bang the butt of the rifle firmly on a hard surface

    a gunsmith told me what makes a good trigger is smooth surfaces and sharp edges
    so polish without rounding anything and look to not remove any material

 

 

Similar Threads

  1. Zastava M70 Trigger Adjustment
    By William in forum Reloading and Ballistics
    Replies: 15
    Last Post: 04-03-2014, 08:35 PM
  2. Hi from Mississippi, USA and a Question about Norinco JW 15 Trigger
    By fullup3 in forum Firearms, Optics and Accessories
    Replies: 3
    Last Post: 12-12-2013, 08:30 AM
  3. RCBS puller & FL die expander ball adjustment
    By ebf in forum Reloading and Ballistics
    Replies: 3
    Last Post: 15-11-2013, 11:58 AM
  4. Lack of adjustment
    By Wildman in forum Firearms, Optics and Accessories
    Replies: 4
    Last Post: 05-12-2011, 09:26 AM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!