Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

ZeroPak DPT


User Tag List

+ Reply to Thread
Page 1 of 2 12 LastLast
Results 1 to 15 of 18
Like Tree13Likes

Thread: Target Camera Revisited

  1. #1
    Member Puffin's Avatar
    Join Date
    May 2012
    Location
    Porirua
    Posts
    970

    Target Camera Revisited

    It’s been a couple of years since 7mmSaum and NZFUBZ presented details of their Target Camera systems:

    https://www.nzhuntingandshooting.co....get-cam-20703/
    https://www.nzhuntingandshooting.co....-camera-26651/

    With the ever-increasing variety of 5.8GHz FPV drone gear available I thought I’d also have a bit of a play with a few options for each of the key parts of a TargetCam system just to see what could be put together while keeping the cost as low as possible. Rather than describing a complete system, here are details of some of the parts tried that I quite liked for one reason or another. In the main these are also parts that offer a slightly different approach to those used in the above systems, so there may be something of interest here to consider for forum members thinking about assembling their own TargetCam.

    For my own application I was after confirmation when shooting at 1km that the first couple of shots were centred on the target - without having to make a 20 minute round trip on foot. I wasn’t sure that 640 x 480 resolution would be sufficient to see all bullet holes in the target, otherwise I would have just bought one of the complete FPV Camera+Tx+Rx+LCDdisplay sets that NZFUBZ linked to, but I also didn’t know if I needed to go full 1080p, plus it seemed a good excuse to have a play with a whole lot of cool FPV gear.

    The prices quoted are all indicative-only, given that AliExpress and Banggood are constantly varying their price discounts. The links will all work at the time the thread is posted. Before there are the usual complaints; no, there aren’t any photos here because all the links provided already picture each of the products from as many angles as you could possibly want.

    Camera

    This one is a new product, inexpensive, and has the resolution to do the job.

    Eachine 1000TVL 1/3 CCD 110 Degree 2.8mm Lens Wide Voltage 5-20V Mini FPV Camera NTSC PAL Switchable
    Banggood Product ID: 1053340
    NZ$16
    https://www.banggood.com/Eachine-100...r_warehouse=CN

    The camera comes with the expected FPV fixed and low focal length / wide angle lens on a standard M12x0.5 thread. This is best replaced with a narrow-angle longer distance lens so the camera can be positioned clear of the line of fire, while still being reasonably front-on to the target. Lately I’ve been using a target board that is 1000mm wide by 700mm. With a 16mm focal length replacement lens this fills the image when the camera is 3.5 metres away and a 25mm lens increases this distance to 6 metres, something like the items linked to below, either work:

    Yumiki 5.0Megpixel M12 MTV 16mm 5MP HD CCTV Camera Lens IR HD Security Camera Lens Fixed Iris
    Product ID: 32792318846
    NZ$7
    https://www.aliexpress.com/item/Yumi...792318846.html

    Witrue M12 5 Megapixel 25mm CCTV lens for HD IP camera F2.0 fixed iris
    Product ID: 32652121758
    NZ$11
    https://www.aliexpress.com/item/VIVE...652121758.html

    Displays

    Stepping the resolution up a little from 640x480 while still being cheaper than fully packaged items are combination loose LCD display and driver boards described as for use in Raspberry Pi projects. These have HDMI, VGA, and AV (RCA socket) inputs. I purchased both of the items listed below to try them out. The LCD screens lack brightness for outside - they are going to need a sunshade for outdoor viewing, and with these loose items this will need to be a DIY job. Match the aspect ratio (4:3 or 16:9) to that of the the camera being used to avoid distorting the image.

    Skylarpu 7” 1024*600 (16:9) IPS Screen Display LCD TFT Monitor EJ070NA-01J with Remote Driver Control Board 2AV HDMI VGA for Raspberry Pi
    AliExpress Product ID: 32709495542
    Price: NZ$36
    https://www.aliexpress.com/item/7-In...709495542.html

    HDMI/VGA/AV Control Driver Board + 8"inch HJ080IA-01E 1024*768 (4:3) IPS high-definition LCD Display For Raspberry Pi
    AliExpress Product ID: 32325924891
    NZ$52
    https://www.aliexpress.com/item/HDMI...325924891.html

    Receiver for use with phone or tablet


    The receiver linked to below allows connection to, and runs off, a smart phone, tablet, or Laptop. So no separate LCD display required, and no separate battery either at the receive end. It is supplied with a short USB cable for this - too short really when you want to get the receiver/antenna well above ground level where the display will likely be. One limitation to date is that the smart phone must be Android. There are descriptions for setting this up with a phone elsewhere online – what app to use etc. For PC viewing I used the free version of NCH Debut. The resolution from this receiver is 640x480. The receiver tunes to the strongest available signal following a scan of the band in 2MHz steps. For PC viewing I used the free version of NCH Debut.

    Eachine ROTG01 UVC OTG 5.8G 150CH Full Channel FPV Receiver For Android Mobile Phone Tablet Smartphone
    Banggood Product ID: 1147692
    NZ$23
    https://www.banggood.com/Eachine-ROT...r_warehouse=CN

    Small patch antenna for more range

    Our application is a bit different from using the gear for FPV in that being fixed point-to-point we don’t need omni-directional antennas and can align polarisation to match at both ends. This means we can go directional to increase system gain for more range.

    FPV 5.8G 5.8Ghz 14dBi High Gain Panel Antenna for Fixed-wing/Multicopter
    Price: NZ $7
    AliExpress Product ID: 32808722856
    https://www.aliexpress.com/item/FPV-...808722856.html

    With all this FPV gear it is necessary to keep track of whether an SMA or Reverse-Polarity SMA antenna connector is used in each case. Although advertised as having an SMA connection, this patch antenna also comes as RP-SMA , selected via what is normally the product colour option:
    Properties: Color Bore (RP SMA)
    Properties: Color Needle (SMA)
    GWH, Beaker, MGNZ and 1 others like this.

  2. #2
    Member Puffin's Avatar
    Join Date
    May 2012
    Location
    Porirua
    Posts
    970
    I included the product details in case the links fail, then maybe the items can still be found from the descriptions.
    Here is a homemade LCD housing. Trying for a 1km path across water here with the rubber duck antenna... not a reliable level of signal and really needs the extra gain from the patch antennas.

    Name:  LCD housing.jpg
Views: 873
Size:  179.8 KB
    Last edited by Puffin; 30-04-2018 at 10:59 PM.
    GWH likes this.

  3. #3
    GWH
    GWH is offline
    Member
    Join Date
    Jul 2012
    Location
    Napier, Hawkes Bay
    Posts
    4,456
    Thanks for posting up all of that, very cool. Looks like one could piece together a neat little setup for bugger all.

    I like the option using a tablet to view.

  4. #4
    Member Puffin's Avatar
    Join Date
    May 2012
    Location
    Porirua
    Posts
    970
    Yes, very little. The receiver for phone option could keep things down to around $60 depending on the day - excluding any additional cost of a battery and tripod at the target end. The combination below for example should work out to 300 metres. Add a patch antenna for 1000m and still only $70.

    Camera, NZ$16
    https://www.banggood.com/Eachine-100...r_warehouse=CN

    Replacement zoom lens, NZ$6
    https://www.banggood.com/16MM-M12-12...r_warehouse=CN

    Transmitter, NZ$17
    https://www.banggood.com/Eachine-TX5...r_warehouse=CN

    Receiver for phone, NZ$23
    https://www.banggood.com/Eachine-ROT...r_warehouse=CN
    GWH and ANOTHERHUNTER like this.

  5. #5
    Member
    Join Date
    Nov 2016
    Location
    Orewa
    Posts
    86
    Thanks for the write up. Been thinking about doing something like this....

    Cheers.

  6. #6
    Member nzfubz's Avatar
    Join Date
    Sep 2012
    Location
    Christchurch
    Posts
    1,146
    Nice work

    Sent from my SM-G950F using Tapatalk
    Diligentia, Vis, Celeritas

  7. #7
    Member Puffin's Avatar
    Join Date
    May 2012
    Location
    Porirua
    Posts
    970
    Update: the particular patch antennas linked to earlier have turned out to be duds. Best to try something else to push the range out to 1km. Maybe look online to see with what models of antenna the FPV community are having success, remembering that circular polarisation is not required for this application. All the other parts are working out well.

  8. #8
    Member Puffin's Avatar
    Join Date
    May 2012
    Location
    Porirua
    Posts
    970
    Further update: the supplied "rubber duck" antennas (as pictured in the earlier photo) at each end will give a video link that runs reliably over 200-300m. For 1-2km where having a video link starts to add real value, then some sort of gain antenna is needed. It is likely that there only needs to be a higher gain antenna at one end, though this will depend on how much gain the antenna is providing. I'd recommend leaving the omni-directional rubber duck at the camera/transmitter end, then the directional antenna can be adjusted easily when back at the shooting position for best picture quality.

    I still think patch antennas should be a good off-the-shelf choice, just not any of the ones that look like the items referred to in the previous post. It might pay to buy in a pair just to be certain of reaching the required distance.
    I did have a play myself and tried something different, ending up building a 19-element yagi. Rock-solid picture over 1km with the transmitter backed off to just 50 milliwatts

    Name:  untitled1.jpg
Views: 574
Size:  131.1 KB

    Name:  untitled2.jpg
Views: 610
Size:  136.5 KB
    WallyR and Cordite like this.

  9. #9
    Caretaker stug's Avatar
    Join Date
    May 2012
    Location
    Rolleston, Canterbury
    Posts
    4,850
    There are some very talented and clever people on this forum.
    WallyR, 40mm and Cordite like this.

  10. #10
    Member
    Join Date
    Nov 2016
    Location
    Orewa
    Posts
    86
    Very nice @<u><a href="https://www.nzhuntingandshooting.co.nz/member.php?u=699" target="_blank">Puffin</a></u>. I was just looking at Yagi ideas the other day and found this guys vid.

    https://youtu.be/UyTaqD3qO4g

    Quote Originally Posted by Puffin View Post
    Further update: the supplied "rubber duck" antennas (as pictured in the earlier photo) at each end will give a video link that runs reliably over 200-300m. For 1-2km where having a video link starts to add real value, then some sort of gain antenna is needed. It is likely that there only needs to be a higher gain antenna at one end, though this will depend on how much gain the antenna is providing. I'd recommend leaving the omni-directional rubber duck at the camera/transmitter end, then the directional antenna can be adjusted easily when back at the shooting position for best picture quality.

    I still think patch antennas should be a good off-the-shelf choice, just not any of the ones that look like the items referred to in the previous post. It might pay to buy in a pair just to be certain of reaching the required distance.
    I did have a play myself and tried something different, ending up building a 19-element yagi. Rock-solid picture over 1km with the transmitter backed off to just 50 milliwatts

    Attachment 88450

    Attachment 88451

  11. #11
    Member specweapon's Avatar
    Join Date
    Apr 2013
    Location
    Tasman
    Posts
    1,042
    It's not a yogi unless it's made out of a Pringles can

  12. #12
    Member Puffin's Avatar
    Join Date
    May 2012
    Location
    Porirua
    Posts
    970
    Quote Originally Posted by MGNZ View Post
    That looks like a design that forum members could have a go at replicating. The driven element is a full-wave loop with unbalanced feed, directors all the same length, I wonder if the designer has quantified the electrical behaviour ? Without building one and testing, it is not so easy to predict, though it looks about right for maybe 9-10dBi forward gain... worth trying.

    The reason I'm harping on a bit about the antennas is that all the other hardware parts have performance that is fixed; the components are purchased in from Banggood or AliExpress, hooked up, and a picture received. It is the choice of antennas when assembling a TargetCam that has the largest influence on whether the system works well - or does not - across the distance required.

    A problem if using the "vertical" antennas supplied with the FPV transmitters and receivers, and one that might not be obvious, is that while the system gain over the distance between the shooter and target may in theory deliver a good picture, these omni-directional "rubber duck" or stick antennae are prone to picking up a multitude of reflected signals that result in the dreaded multi-path interference. Very small changes in the position of the receiver or things close to the receiver (think you or the rifle etc) can cause the video to repeatedly drop out. A directional antenna at the receiving end is a good thing not just because it provides some forward gain but because it suppresses (for want of a better term) the pick up of signals from directions other than from the target, and makes the quality of the link more robust. If using the supplied stick antennas, having your shooting position with the TargetCam receiving antenna out in the open and clear of the ground will be better than near structures, particular metal ones.

  13. #13
    Gone................. mikee's Avatar
    Join Date
    Aug 2012
    Location
    Nelson, New Zealand
    Posts
    9,647
    I built a target cam using 2 of these, (currently disassembled as I need the camera for something else) but it worked well to 1600m and I could control (zoom) the camera in.
    Could see the image on my Cell but was a bit of fannying about to get working and really was more of a permanent installation. Going to reassemble it with a solar panel and controller and leave it in position eventually
    Puffin likes this.
    All those with dogs waiting no longer fear death. Those with many dogs waiting even welcome it in it's time.

  14. #14
    Member Cordite's Avatar
    Join Date
    May 2017
    Location
    NZ Mainland (Dunedin)
    Posts
    5,478
    Just thinking about lighter, integrated solutions.

    How far out would a DSLR (fully zoomed and mounted on a steady low tripod) be useful for paper target spotting using its preview screen?
    An itch ... is ... a desire to scratch

  15. #15
    Member Cordite's Avatar
    Join Date
    May 2017
    Location
    NZ Mainland (Dunedin)
    Posts
    5,478
    Quote Originally Posted by Puffin View Post
    Further update: the supplied "rubber duck" antennas (as pictured in the earlier photo) at each end will give a video link that runs reliably over 200-300m. For 1-2km where having a video link starts to add real value, then some sort of gain antenna is needed. It is likely that there only needs to be a higher gain antenna at one end, though this will depend on how much gain the antenna is providing. I'd recommend leaving the omni-directional rubber duck at the camera/transmitter end, then the directional antenna can be adjusted easily when back at the shooting position for best picture quality.

    I still think patch antennas should be a good off-the-shelf choice, just not any of the ones that look like the items referred to in the previous post. It might pay to buy in a pair just to be certain of reaching the required distance.
    I did have a play myself and tried something different, ending up building a 19-element yagi. Rock-solid picture over 1km with the transmitter backed off to just 50 milliwatts

    Attachment 88450

    Attachment 88451
    @Puffin

    Most beautiful Yagi I've seen! Thanks for adding the match to show the size.

    NB, at higher frequencies, RF runs primarily at the surface of copper elements, so surface oxidation can become an issue over time. I'd suggest complete the Yagi by polishing the copper and doing an overspray/brush with protective topcoat.

    Would you be happy posting an image of the schematics for your Yagi?
    An itch ... is ... a desire to scratch

 

 

Similar Threads

  1. Target Camera
    By nzfubz in forum Projects and Home Builds
    Replies: 16
    Last Post: 21-06-2023, 09:42 AM
  2. Bearing length revisited
    By r87mm in forum Reloading and Ballistics
    Replies: 0
    Last Post: 25-11-2017, 01:59 PM
  3. TargetVision LR-2 Target Camera
    By Dermastor in forum Firearms, Optics and Accessories
    Replies: 7
    Last Post: 18-04-2017, 07:19 PM
  4. Spot X revisited
    By Chris in forum Fishing
    Replies: 10
    Last Post: 22-03-2015, 09:29 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!