338MAN mk2
Member

121 Likes

Page 1 of 9 123456789 Last

• Jump to page:

1. 
   338MAN mk2 liked post by mawzer308 On thread : Stags shot 2026

   Just an FYI, he won't score and won't go in the books if he's soft. In good condition for sure.

   Liked On: 12-01-2026, 09:04 PM

2. 
   338MAN mk2 liked post by Allgood On thread : No such thing as overkill

   After reading this thread I think I might get the 1908 Mauser Model B in 10.75 x 68 out of the safe and take it for a walk......

   Liked On: 11-01-2026, 04:42 PM

3. 
   338MAN mk2 liked post by madjon_ On thread : Case trimming;Ugly

   Don't shout, I start rocking and sucking my thumb 👍 :D

   Liked On: 09-01-2026, 05:13 PM

4. 
   338MAN mk2 liked post by mawzer308 On thread : No such thing as overkill

   Bit gory but yes a bit of damage on the shoulder. 290321

   Liked On: 09-01-2026, 02:34 PM

5. 
   338MAN mk2 liked post by craigc On thread : Thermal Pest Control

   Yeah! ;-)

   Liked On: 27-12-2025, 09:20 PM

6. 
   338MAN mk2 liked post by No good names left On thread : Thermal Pest Control

   Both of them ?

   Liked On: 27-12-2025, 09:20 PM

7. 
   338MAN mk2 liked post by Tahr On thread : Bullet Blew Up. Is it a thing?

   Plenty of talk about bullets being too soft for close shots and bullets "blowing up". But does it really matter and how often are animals actually wounded and lost? My limited experience is that bits...

   Liked On: 22-12-2025, 06:27 PM

8. 
   338MAN mk2 liked post by Friwi On thread : 338 ARC - An Early Guess At Reloading Data

   Shot a big hind last night at 140m. I had to finish her once I found her as I only got one lung and not the other (3/4 forward shot). I shot a few goats as well but did not have time to otopsy them...

   Liked On: 11-12-2025, 09:00 PM

9. 
   338MAN mk2 liked post by Deanohit On thread : Titegroup for various subsonic loads?

   I experimented with fillers, I didn't see any improvement in accuracy but I did notice my suppressors catching some of the fillers. The 223 load is not as accurate as 22lr but its easily enough to...

   Liked On: 24-11-2025, 12:27 PM

10. 
    338MAN mk2 liked post by 30.06king On thread : seating die is pulling out bullets

    Weak neck tension. Is this the first loading in new brass ? If so, pays to run the brass through a neck or FL sizer die to even up neck sizing and ( hopefully ) ensure ther will be sufficient...

    Liked On: 25-10-2025, 09:53 PM

11. 
    338MAN mk2 liked post by fawkes On thread : Older timers..

    That and Hoppes No 9 - and fired paper shotshells

    Liked On: 03-10-2025, 01:59 PM

12. 
    338MAN mk2 liked post by Tahr On thread : click click boom

    Good hunt. Its almost never the primer.

    Liked On: 29-09-2025, 08:58 AM

13. 
    338MAN mk2 liked post by gimp On thread : Quick annealing experiment

    .223 ADI brass, same lot. FL sized down and expanded up again with a 6mm expander mandrel til neck split. Top case no annealing, 7x. Middle and bottom case, annealed each time (different durations),...

    Liked On: 28-08-2025, 09:48 PM

14. 
    338MAN mk2 liked post by TeRei On thread : Primer failure rate.

    So does annealed brass and correct FLS. It is not rocket science but some get it horribly wrong.

    Liked On: 28-08-2025, 09:45 PM

15. 
    338MAN mk2 liked post by Longranger On thread : Primer failure rate.

    You need to anneal the neck AND the shoulder for consistent headspace....any full length die should be capable of achieving that. I full length size every time and check each round in the chamber...

    Liked On: 28-08-2025, 09:44 PM

Page 1 of 9 123456789 Last

• Jump to page: