diana2
Member

302 Likes

Page 2 of 21 First 12345678910111213141516 ... Last

• Jump to page:

1. 
   diana2 liked post by Hutch On thread : What ammo works well in your fully suppr.10/22 ?

   I have a fully suppressed 10/20 built by the guy in Nelson, one of the original "Bunny Busters" before he stopped doing them. Runs well on CCI & Winchester 40gn subsonics. He did tune them for...

   Liked On: 02-09-2024, 09:59 PM

2. 
   diana2 liked post by Jhon On thread : What ammo works well in your fully suppr.10/22 ?

   Winchester HP excellent

   Liked On: 28-08-2024, 09:10 PM

3. 
   diana2 liked post by 7mm tragic On thread : What ammo works well in your fully suppr.10/22 ?

   CCI sub sonic 40gr hollow point. one ragged hole at 50 yards CCI standard velocity target. One ragged hole at 50 yards

   Liked On: 28-08-2024, 09:10 PM

4. 
   diana2 liked post by jusepy81 On thread : What ammo works well in your fully suppr.10/22 ?

   CCI subs , I have the polymer buffer and is supressed. The only problem I have come across is the magazine becoming very dirty from the wax from the subs and that causes the 10/22 to...

   Liked On: 28-08-2024, 09:10 PM

5. 
   diana2 liked post by Shearer On thread : What ammo works well in your fully suppr.10/22 ?

   I have a 10/22 competition and it cycles CCI subsonic fine.

   Liked On: 28-08-2024, 09:09 PM

6. 
   diana2 liked post by csmiffy On thread : What ammo works well in your fully suppr.10/22 ?

   Going back over 5 years I tried some new winchester 42gr subsonics. Made in the US now. The only ammo that my 10/22 didn't work with. I may have clipped the spring, but that was years ago and can't...

   Liked On: 28-08-2024, 09:09 PM

7. 
   diana2 liked post by AR7 On thread : What ammo works well in your fully suppr.10/22 ?

   Hi diana2 every rifle likes certain brands /weights of ammo you say you have a fully suppressed barrel ,how long is the barrel [rifling ] has the barrel been ported .. Have you cut the...

   Liked On: 28-08-2024, 09:09 PM

8. 
   diana2 liked post by tibo On thread : What ammo works well in your fully suppr.10/22 ?

   did you try CCI suppressor and Tac22?

   Liked On: 28-08-2024, 04:19 PM

9. 
   diana2 liked post by Wurzelmangler On thread : Knifemaking photo-essay (9) Finishing and sharpening

   These images give an idea of the knife’s size. I’ll conclude this photo-essay by mentioning that I sometimes get asked how long it takes me to make one of my full-tang knives. They can take from 8...

   Liked On: 11-06-2024, 08:58 PM

10. 
    diana2 liked post by Wurzelmangler On thread : Knifemaking photo-essay (8) Shaping the guard

    1) Sanding the spine with a 180 grit belt. 2) I sand the butt curve on the unsupported (slack) belt as indicated by the pink arrow. 3) 180 grit sanding of the sides. 4) 180 grit sanding of...

    Liked On: 10-06-2024, 03:34 PM

11. 
    diana2 liked post by Wurzelmangler On thread : Knifemaking photo-essay (6) Fitting the handle slabs

    1) Flattening the side of the slab that will be glued to the tang. To do this job, a disc sander is better than a belt sander. 2) Angling the front of the slab. The dovetail cutter cuts an 11...

    Liked On: 06-06-2024, 05:16 PM

12. 
    diana2 liked post by Wurzelmangler On thread : Knifemaking photo-essay (4) Soldering the guard

    1) Sanding the protruding top of the guard so it’s level with the spine. Metal dust is generated during this step. I have to emphasize that, to avoid any possibility of lead poisoning, the solder...

    Liked On: 02-06-2024, 03:45 PM

13. 
    diana2 liked post by Wurzelmangler On thread : Knifemaking photo-essay (2)

    1) I’ve swapped out the surface grinder’s belt sanding attachment for a fine white grinding wheel. A machine vice, which is bolted to a thick steel plate, is placed on the magnetic vice. I’m aligning...

    Liked On: 28-05-2024, 05:36 PM

14. 
    diana2 liked post by Wurzelmangler On thread : Knifemaking photo-essay (1)

    Three views of the knife blank. Note that, even though I don’t use a grinding jig, the edge is centred (bottom image).

    Liked On: 27-05-2024, 09:53 AM

15. 
    diana2 liked post by Wurzelmangler On thread : Knifemaking photo-essay (1)

    1) Finishing the profile grind using a flat platen linisher. 2) Grinding the curve at the butt. 3) Forming the finger grooves using a narrow-radius linisher. 4) Removing the hard black oxide...

    Liked On: 27-05-2024, 09:52 AM

Page 2 of 21 First 12345678910111213141516 ... Last

• Jump to page: