grandpamac
Member

4208 Likes

Page 120 of 281 First ... 2070106107108109110111112113114115116117118119120121122123124125126127128129130131132133134170220 ... Last

• Jump to page:

1. 
   on2it liked post by grandpamac On thread : Taupo NZDA range

   Greetings All, I think that the future use of ranges is clear. We should all join a club that has its own or access to a range. I joined Taupo NZDA about 20 years ago after the Roys Hill Range here...

   Liked On: 18-07-2022, 03:25 PM

2. 
   Danny liked post by grandpamac On thread : Reload data on internet

   Greetings All, Just another not so gentle reminder that we should not use data from any scource (including this forum) without verifying it from pressure tested data. Way back when my hair was...

   Liked On: 18-07-2022, 02:43 PM

3. 
   mudgripz liked post by grandpamac On thread : Best .22 value for money?

   Greetings All, Almost any .22 RF will shoot well given decent sights and trigger. There are half a dozen here at the moment of which half are favourites. My 10-22 sporter, bought new over 50 years...

   Liked On: 18-07-2022, 01:32 PM

4. 
   foxhound liked post by grandpamac On thread : 8mm mauser, AR2209

   Greetings, People tend to forget that the 8 x57 is easily the equal of the .30-06 when loaded to the same pressure. AR2209 is a great powder in either cartridge as long as the .30-06 is not fired in...

   Liked On: 15-07-2022, 03:25 PM

5. 
   BSA270 liked post by grandpamac On thread : reloading companies to reload 7-08 for me

   Greetings Northkiwi, If you haven't already done it a visit to the Whangarei NZDA Branch could be worthwhile. There will probably be someone there who could mentor you getting into handloading. You...

   Liked On: 13-07-2022, 09:45 PM

6. 
   Stefanhope liked post by grandpamac On thread : Anyone using 7mm 154sst with 2217

   Greetings Stefanhope and all, H1000 was originally manufactured by Nobels from the 1980's and from the late 1990's by ADI as AR2217. Over this period the industry changed from the old copper crusher...

   Liked On: 13-07-2022, 08:05 PM

7. 
   planenutz liked post by grandpamac On thread : reloading companies to reload 7-08 for me

   Greetings Northkiwi, If you haven't already done it a visit to the Whangarei NZDA Branch could be worthwhile. There will probably be someone there who could mentor you getting into handloading. You...

   Liked On: 13-07-2022, 12:11 PM

8. 
   40mm liked post by grandpamac On thread : reloading companies to reload 7-08 for me

   Greetings Northkiwi, If you haven't already done it a visit to the Whangarei NZDA Branch could be worthwhile. There will probably be someone there who could mentor you getting into handloading. You...

   Liked On: 12-07-2022, 08:02 PM

9. 
   nigelp liked post by grandpamac On thread : Split brass

   Greetings again all, I could have been clearer in my earlier post. The early head separations in belted cases can be as much a rifle problem as a case problem. The belt recess in some belted...

   Liked On: 12-07-2022, 11:55 AM

10. 
    Tertle liked post by grandpamac On thread : H4895 in 223

    Greetings bumblefoot and all, AR2206H (H4895) is currently my go to powder for my .223, .308 and .303 rIfles. In my T3x .223 25.5 grains with the 55 grain projectile gives 3,130 fps from the...

    Liked On: 11-07-2022, 10:22 PM

11. 
    rupert liked post by grandpamac On thread : STRAIGHTENING A CROOKED BULLET

    Greetings All, John Barsness, one of my favourite handloading writers, had an article in Handloader mag recently. He looked at reasons for projectile run out and identified the expander ball as a...

    Liked On: 10-07-2022, 02:23 PM

12. 
    veitnamcam liked post by grandpamac On thread : STRAIGHTENING A CROOKED BULLET

    Greetings All, John Barsness, one of my favourite handloading writers, had an article in Handloader mag recently. He looked at reasons for projectile run out and identified the expander ball as a...

    Liked On: 10-07-2022, 12:31 PM

13. 
    JohnDuxbury liked post by grandpamac On thread : STRAIGHTENING A CROOKED BULLET

    Greetings All, John Barsness, one of my favourite handloading writers, had an article in Handloader mag recently. He looked at reasons for projectile run out and identified the expander ball as a...

    Liked On: 10-07-2022, 12:30 PM

14. 
    Mathias liked post by grandpamac On thread : STRAIGHTENING A CROOKED BULLET

    Greetings All, John Barsness, one of my favourite handloading writers, had an article in Handloader mag recently. He looked at reasons for projectile run out and identified the expander ball as a...

    Liked On: 10-07-2022, 10:34 AM

15. 
    Ingrid 51 liked post by grandpamac On thread : Reloading room and equipment upgrade - first step

    Thats two of us using an old school desk. Much easier to put in the back of your vehicle to take it to the range though. Regards Grandpamac.

    Liked On: 09-07-2022, 07:04 PM

Page 120 of 281 First ... 2070106107108109110111112113114115116117118119120121122123124125126127128129130131132133134170220 ... Last

• Jump to page: