grandpamac
Member

4758 Likes

Page 266 of 318 First ... 166216252253254255256257258259260261262263264265266267268269270271272273274275276277278279280316 ... Last

• Jump to page:

1. 
   Micky Duck liked post by grandpamac On thread : 6.5 cm case capacity

   Greetings Wild Brad, Trickling the charge in to the case and tapping the part full case on the bench can help get a bit more in. Someone may be able to help with case weights but Winchester is often...

   Liked On: 06-02-2021, 04:19 PM

2. 
   Micky Duck liked post by grandpamac On thread : Load Development - Velocity vs Accuracy

   Greetings All, We have now drifted into the world of Psychology. Bos is likely wondering what he started. There is no doubt that we all are effected by how we think about things and have to make our...

   Liked On: 06-02-2021, 12:29 PM

3. 
   Finnwolf liked post by grandpamac On thread : Load Development - Velocity vs Accuracy

   Greetings Bos, Further to what Micky has shared above I also have a question. If you have tested the load out at say 300 yards and there is no vertical stringing then I am with Micky all the way....

   Liked On: 05-02-2021, 08:17 PM

4. 
   Micky Duck liked post by grandpamac On thread : Load Development - Velocity vs Accuracy

   Greetings Bos, Further to what Micky has shared above I also have a question. If you have tested the load out at say 300 yards and there is no vertical stringing then I am with Micky all the way....

   Liked On: 05-02-2021, 06:40 PM

5. 
   Moa Hunter liked post by grandpamac On thread : Load Development - Velocity vs Accuracy

   Greetings Bos, Further to what Micky has shared above I also have a question. If you have tested the load out at say 300 yards and there is no vertical stringing then I am with Micky all the way....

   Liked On: 05-02-2021, 06:40 PM

6. 
   Micky Duck liked post by grandpamac On thread : The Importance of Using the Right Data

   Greetings NRT, Thanks for your candid sharing of your load data with us. As above both are in the safe zone and I am sure work well for you. With regards about bolt actions being strong this is true...

   Liked On: 04-02-2021, 08:09 PM

7. 
   tikka liked post by grandpamac On thread : Kimber Montana 308 Load Development

   Greetings Tikka 7mm-08, A note of caution. The 168 grain ABLR will develop more pressure than the 165 grain Hornady so you will probably need to cut those loads a grain or two. I would use the...

   Liked On: 04-02-2021, 06:22 PM

8. 
   Tikka7mm08 liked post by grandpamac On thread : Kimber Montana 308 Load Development

   Greetings Tikka 7mm08, Looks like you have your load for the big stuff sorted. Perhaps an understudy load with one of the excellent 125 or 130 grains projectiles available these days may be in order...

   Liked On: 04-02-2021, 06:12 PM

9. 
   Moa Hunter liked post by grandpamac On thread : New to reloading - to what fraction of a grain do you test new loads? 0.5gr, 0.3gr...

   Greetings Pav, Your question above got me thinking. Rather than major changes I seem to have refined the process as my understanding of it has increased. Initially I was limited partly by my...

   Liked On: 02-02-2021, 06:49 PM

10. 
    Micky Duck liked post by grandpamac On thread : The Importance of Using the Right Data

    Greetings Moa Hunter, Proof cartridges are rated for pressure and not load. The powders used are unlikely to be anything we have heard of. Pressures are significantly above the standard cartridges....

    Liked On: 30-01-2021, 11:35 PM

11. 
    veitnamcam liked post by grandpamac On thread : The Importance of Using the Right Data

    Greetings Moa Hunter, Proof cartridges are rated for pressure and not load. The powders used are unlikely to be anything we have heard of. Pressures are significantly above the standard cartridges....

    Liked On: 30-01-2021, 11:59 AM

12. 
    Moa Hunter liked post by grandpamac On thread : The Importance of Using the Right Data

    Greetings All, The weather today is all warm and horrible in Hawkes Bay and the white flag was run up on splitting firewood early on. I thought it might be interesting to look at the variations in...

    Liked On: 29-01-2021, 04:19 PM

13. 
    Phil_H liked post by grandpamac On thread : .270wsm who has one???

    Greetings Phil, Just wait a bit. There are bound to be at least three more whizo calibres out by the end of the year. All more powerful than a locomotive and able to leap tall buildings in a single...

    Liked On: 27-01-2021, 07:21 PM

14. 
    keneff liked post by grandpamac On thread : Best adi powder data

    Greetings All, Apologies from me also. In penance I remind all that all tested load data for the Hodgdon/ ADI powders can be used for loads for the ADI powders. These are the same powders, made in...

    Liked On: 25-01-2021, 11:30 PM

15. 
    ZQLewis liked post by grandpamac On thread : The Importance of Using the Right Data

    Greetings All, The recent thread on the best data for ADI powder got me thinking. Data has changed over time for various reasons so I thought I would share some comparisons to illustrate why current...

    Liked On: 25-01-2021, 10:46 PM

Page 266 of 318 First ... 166216252253254255256257258259260261262263264265266267268269270271272273274275276277278279280316 ... Last

• Jump to page: