Hunter_killer
Member

323 Likes

Page 3 of 22 First 1234567891011121314151617 ... Last

• Jump to page:

1. 
   Hunter_killer liked post by stagstalker On thread : 7mmRM project

   Tikka 24” factory fluted barrel mate.

   Liked On: 03-03-2019, 03:11 PM

2. 
   Hunter_killer liked post by gonetropo On thread : Are these electronic ear muffs ok? $45 in GC sale

   buy peltors, your hearing is worth it

   Liked On: 03-03-2019, 02:06 PM

3. 
   Hunter_killer liked post by Tommy On thread : Are these electronic ear muffs ok? $45 in GC sale

   With either I would wear foam plugs underneath if there's a lot of shooting going on, or if shooting from under cover. You can still hear conversation through the plugs when there's no shooting....

   Liked On: 03-03-2019, 08:49 AM

4. 
   Hunter_killer liked post by uk_exile On thread : Are these electronic ear muffs ok? $45 in GC sale

   https://www.guncity.com/barricade-electronic-earmuffs-21-db-343669 Just starting out. Do I get these or are they crap & simple foam plugs would be better?

   Liked On: 03-03-2019, 08:14 AM

5. 
   Hunter_killer liked post by Tussock On thread : Rusted bolt carrier group

   I ripped into this today. Been sitting in Blaster waiting for me to get 5 spare moments. Everything came apart with big chunks of rust flaking off. I have photos. First meths and a plastic pot...

   Liked On: 02-03-2019, 04:21 PM

6. 
   Hunter_killer liked post by Cigar On thread : Scope advice

   Just in case you aren't aware, with most scope rings there is a gap between the top and bottom pieces - they aren't cranked down until they meet. Looks like the guy you got the scope from may not...

   Liked On: 01-03-2019, 10:04 PM

7. 
   Hunter_killer liked post by mawzer308 On thread : Scope advice

   Yes lapping will take a very small amount of material off and it ensures that the surface area on the rings is all the same. So when the rings are tightened it contacts evenly with the scope so there...

   Liked On: 01-03-2019, 10:04 PM

8. 
   Hunter_killer liked post by Carpe Diem On thread : Bit of loopy help

   I can bring my VX cds down Friday to compare. You don't think young sir has retightened the rings for dad - thinking I'll sort it out for him? buckling the tube through torque??? But my gut I...

   Liked On: 01-03-2019, 06:20 PM

9. 
   Hunter_killer liked post by quentin On thread : Scope advice

   Those rings don't look like any vortex rings I have come across before. If I was to hazard a guess, I'd say Chinese made. Will be interesting to see how much material gets removed if you were to lap...

   Liked On: 01-03-2019, 05:20 PM

10. 
    Hunter_killer liked post by ChrisW On thread : Scope advice

    Iv seen this several times. Generally once the tube is dented it wont track properly and may not hold a zero.

    Liked On: 01-03-2019, 05:20 PM

11. 
    Hunter_killer liked post by gonetropo On thread : Scope advice

    in retrospect i am wrong, they would be side crushed but the size difference would be so huge you would need to be the hulk to squeeze down a 25mm ring on a 30mm tube. 25mm ring on a 1" tube is...

    Liked On: 01-03-2019, 03:53 PM

12. 
    Hunter_killer liked post by gonetropo On thread : Scope advice

    if it were possible it would be crushed top to bottom not at the "equator" (where the rings meet)

    Liked On: 01-03-2019, 03:27 PM

13. 
    Hunter_killer liked post by Delphus On thread : Scope advice

    Hey so I just noticed the scope rings that came with my second hand vortex diamondback have crimped the tube a bit. It's quite an obvious dent. Will this affect the scope at all? The guy told me they...

    Liked On: 01-03-2019, 03:03 PM

14. 
    Hunter_killer liked post by stagstalker On thread : 7mmRM project

    I think I have some 2217 left over here in manawatu you could try if you wanted. My rem mag flat out hated it with the 162 ELDX haha. Using IMR 4831 now.

    Liked On: 01-03-2019, 07:46 AM

15. 
    Hunter_killer liked post by winaa On thread : 7mmRM project

    I see the point of confusion here I typed 63.5 OAL where in fact I used 85.0 OAL as stated in your first post. I was looking at the "case length' when i typed it. Sorry for the mix up

    Liked On: 28-02-2019, 10:46 AM

Page 3 of 22 First 1234567891011121314151617 ... Last

• Jump to page: