johnd
Member

742 Likes

Page 13 of 50 First 123456789101112131415161718192021222324252627 ... Last

• Jump to page:

1. 
   johnd liked post by akaroa1 On thread : Who's seen a rimfire do this before

   Wrong roll Mark on barrel It's really a 22 HMR and you were using the wrong caliber ammo

   Liked On: 18-06-2022, 10:17 PM

2. 
   johnd liked post by keengunNic On thread : FX 120i and auto trickler

   I love my A&D120i and v3 combo. Fast, accurate and consistent as. Threw 200 6mm loads today and seated them in about an hour and 45. I was faffing about a little too. I went from the lee balance...

   Liked On: 18-06-2022, 07:18 PM

3. 
   johnd liked post by gqhoon On thread : FX 120i and auto trickler

   I’ve got a A&D300 with V4 and it’s life-changing compared to the RCBS Chargemaster I used to have! Not from a speed perspective (both throw about the same rate), but from the peace of mind that the...

   Liked On: 18-06-2022, 07:18 PM

4. 
   johnd liked post by Young_sika_hntr On thread : Sika Roar 2022 youtube vid

   Sika roar 2022 youtube video for anyone interested. cheers  https://www.youtube.com/watch?v=zsnE9kbZAlk

   Liked On: 12-06-2022, 01:53 AM

5. 
   johnd liked post by Bill999 On thread : Covering ceracoat

   A non permanent idea could be the car alloy wheel spray paint, you lay it on thick and it peals off when you are sick of it like rubber stretches No doubt it will wear but it’s non committal if you...

   Liked On: 11-06-2022, 05:04 PM

6. 
   johnd liked post by Micky Duck On thread : Covering ceracoat

   you could go the horse bandage route....... or insulation tape,its not as agricultural as might first think if you do it carefully...my S/S Howa has a large section of the barrel covered by single...

   Liked On: 11-06-2022, 03:11 AM

7. 
   johnd liked post by XR500 On thread : Cut vs split firewood

   The older you get the crunchier your shoulder joints sound. I used to split 15 odd cube for a year's firewood by hand. Then after about ten years abuse on the body I bought a hydraulic splitter and...

   Liked On: 11-06-2022, 12:43 AM

8. 
   johnd liked post by Moa Hunter On thread : Covering ceracoat

   Ask a panel beater if they have a two pot epoxy that will go over it

   Liked On: 11-06-2022, 12:39 AM

9. 
   johnd liked post by caberslash On thread : Sako vixen options

   You are probably better off with either a Howa Mini or Rem Model 7 TBH, off the shelf replacement components available, can be picked up relatively cheap 'Flaws' of the Sako Vixen - Sako...

   Liked On: 18-05-2022, 08:26 PM

10. 
    johnd liked post by LBD On thread : 7/8 x 14 plastic threaded rod

    I agree totally with your last thought..... Get a can of Tectyl 506 and give it a wee spray... if you want tidy then go to your local hydraulic hose shop and get a couple of plastic plugs to keep...

    Liked On: 13-05-2022, 12:45 PM

11. 
    johnd liked post by Micky Duck On thread : 7/8 x 14 plastic threaded rod

    ice cream container filled with 2stroke fuel...drop the dies in,leave for awhile and take back out....job done. it sure cleans out the crap.

    Liked On: 12-05-2022, 08:13 PM

12. 
    johnd liked post by winaa On thread : 7/8 x 14 plastic threaded rod

    Most plastic plugs or threaded tube will be BSP. You could go to a local Engineering shop and get them make you one up out of 1inch or 1 1/8 PVC hex if they have some. Just be aware that you will...

    Liked On: 12-05-2022, 08:12 PM

13. 
    johnd liked post by Kelton On thread : 7/8 x 14 plastic threaded rod

    https://www.marine-deals.co.nz/bungs-drain-plugs/expanding-bung-and-drain-plug?gclid=CjwKCAjwve2TBhByEiwAaktM1DeNw4hhIkFVm415R1mTYYA1DUdY9oT29mGmoTzyHwYrYJfgjW_DhhoCE_sQAvD_BwE This could work...

    Liked On: 12-05-2022, 08:12 PM

14. 
    johnd liked post by Kelton On thread : 7/8 x 14 plastic threaded rod

    Iv got an old die I spray with oil and leave in their as mine were going very rusty spray my dies when putting them away now to

    Liked On: 12-05-2022, 06:36 PM

15. 
    johnd liked post by Bos On thread : "Best" Digital scales around

    Had a look at a mates Frankford Arsenal Auto Trickler last night, Bought it from Reloaders Supplies and looks pretty impressive. Reackons its easy to use and measures to .01 of a grain Might be the...

    Liked On: 09-05-2022, 08:53 PM

Page 13 of 50 First 123456789101112131415161718192021222324252627 ... Last

• Jump to page: