Kelton
Member

1487 Likes

Page 20 of 100 First ... 67891011121314151617181920212223242526272829303132333470 ... Last

• Jump to page:

1. 
   7mmsaum liked post by Kelton On thread : Reloading 7mm Rem mag

   You cant unread what you have read but you can ignore it iv loaded 100s apon 100s of rem mag rounds and never had an issue

   Liked On: 22-08-2023, 06:56 PM

2. 
   rewa liked post by Kelton On thread : friends asking how much for load development

   I think theirs a joker in tauranga charging about $500 for load d then maybe abit more than a dollar around $1.50 . Its a timly beast and I no your results are spot on so if you happy with that run...

   Liked On: 21-08-2023, 09:03 PM

3. 
   Bill999 liked post by Kelton On thread : Bipod heights

   Iv got the mountain I went for the long dins it brilliant shooting over banks and up hill in longer grass il measure . dannyb both adjustable they donthe splits to which helps get higher or lower...

   Liked On: 21-08-2023, 08:38 AM

4. 
   7mm Rem Mag liked post by Kelton On thread : Storing powder, can you over fill

   I tip all mine in a bucket (clean bucket) and shake it up to try blend batch to batch

   Liked On: 19-08-2023, 10:25 PM

5. 
   Micky Duck liked post by Kelton On thread : Storing powder, can you over fill

   I tip all mine in a bucket (clean bucket) and shake it up to try blend batch to batch

   Liked On: 19-08-2023, 10:15 PM

6. 
   superdiver liked post by Kelton On thread : Short barrel powders (308 and 7mm RM)

   Also plenty of reloader 22 around but it sounds like a temp sensitive powder id be using 168amax and 162 eldm/x. Or 178eldm in the 308 but the 168 is very impressive i load it in a 16" and an 18" ...

   Liked On: 19-08-2023, 04:03 PM

7. 
   dannyb liked post by Kelton On thread : Bipod heights

   Thats the 12" mate i imagen the 8" would be around 11" to under side of fore end . The 8" has less range of movements though im not sure it does the splits some reading would be recommended

   Liked On: 19-08-2023, 02:27 PM

8. 
   Jus liked post by Kelton On thread : Short barrel powders (308 and 7mm RM)

   Yip iv shot over 3000 with 2225 and 175eldx in a 85 finnlight

   Liked On: 19-08-2023, 09:23 AM

9. 
   dannyb liked post by Kelton On thread : Bipod heights

   It measures 15.5 inchs from feet to bottom of fore end when extended and half of that with legs retracted but then with the splits it gets as low as 3 inchs

   Liked On: 19-08-2023, 08:34 AM

10. 
    dannyb liked post by Kelton On thread : Bipod heights

    Iv got the mountain I went for the long dins it brilliant shooting over banks and up hill in longer grass il measure . dannyb both adjustable they donthe splits to which helps get higher or lower...

    Liked On: 19-08-2023, 08:23 AM

11. 
    GlenM liked post by Kelton On thread : Short barrel powders (308 and 7mm RM)

    Also plenty of reloader 22 around but it sounds like a temp sensitive powder id be using 168amax and 162 eldm/x. Or 178eldm in the 308 but the 168 is very impressive i load it in a 16" and an 18" ...

    Liked On: 19-08-2023, 07:42 AM

12. 
    6.5 CRD liked post by Kelton On thread : Short barrel powders (308 and 7mm RM)

    2217 in the rem mag and 2206h in 308

    Liked On: 19-08-2023, 06:21 AM

13. 
    flock liked post by Kelton On thread : Short barrel powders (308 and 7mm RM)

    2217 in the rem mag and 2206h in 308

    Liked On: 18-08-2023, 10:58 PM

14. 
    7mmsaum liked post by Kelton On thread : Short barrel powders (308 and 7mm RM)

    2217 in the rem mag and 2206h in 308

    Liked On: 18-08-2023, 10:51 PM

15. 
    chainsaw liked post by Kelton On thread : Short barrel powders (308 and 7mm RM)

    2217 in the rem mag and 2206h in 308

    Liked On: 18-08-2023, 10:39 PM

Page 20 of 100 First ... 67891011121314151617181920212223242526272829303132333470 ... Last

• Jump to page: