kiwi303
Member

105 Likes

Page 7 of 7 First 1234567

• Jump to page:

1. 
   zimmer liked post by kiwi303 On thread : Forster Full legth dies - Tight?

   I use a hornady head space comparitor, zero the vernier on a fired case and slowly adjust the die down until i get -2 though. I have a hornady press and each die has its own bushing so once I set it...

   Liked On: 08-07-2021, 06:23 PM

2. 
   rewa liked post by kiwi303 On thread : Matches with hunting bullets

   BC 100% does matter at field matches. BC directly effects wind drift. the less drift you have the more tolerance you have in a slightly off wind call. In saying that I shoot a lot of PRS/field...

   Liked On: 03-07-2021, 03:20 PM

3. 
   Micky Duck liked post by kiwi303 On thread : Matches with hunting bullets

   BC 100% does matter at field matches. BC directly effects wind drift. the less drift you have the more tolerance you have in a slightly off wind call. In saying that I shoot a lot of PRS/field...

   Liked On: 02-07-2021, 08:20 PM

4. 
   Nathanfish liked post by kiwi303 On thread : Custom turrets and sea level heights

   if you run the numbers even with a 1500m altitude change it doesn't significantly effect your bullet out to 500m (about 1 ich). once you start getting past 500m you do need to start considering your...

   Liked On: 08-06-2021, 04:24 PM

5. 
   Mick Hunter liked post by kiwi303 On thread : Looking for mentor Taupo/ CNI

   Hi mate, Flick me a PM, I'm not around very often in the weekends but would happily help one day after work. Am located in Taupo Cheers

   Liked On: 12-05-2021, 01:35 PM

6. 
   Micky Duck liked post by kiwi303 On thread : Looking for mentor Taupo/ CNI

   Hi mate, Flick me a PM, I'm not around very often in the weekends but would happily help one day after work. Am located in Taupo Cheers

   Liked On: 11-05-2021, 06:17 PM

7. 
   Pushover liked post by kiwi303 On thread : Looking for mentor Taupo/ CNI

   Hi mate, Flick me a PM, I'm not around very often in the weekends but would happily help one day after work. Am located in Taupo Cheers

   Liked On: 11-05-2021, 05:15 PM

8. 
   bunji liked post by kiwi303 On thread : Looking for mentor Taupo/ CNI

   Hi mate, Flick me a PM, I'm not around very often in the weekends but would happily help one day after work. Am located in Taupo Cheers

   Liked On: 11-05-2021, 04:15 PM

9. 
   Preacher liked post by kiwi303 On thread : Looking for mentor Taupo/ CNI

   Hi mate, Flick me a PM, I'm not around very often in the weekends but would happily help one day after work. Am located in Taupo Cheers

   Liked On: 11-05-2021, 04:08 PM

10. 
    northdude liked post by kiwi303 On thread : All things BSA

    122296 This BSA started off standard and in british hand in ww2 Following the war it was acquired by the Israeli's who made the scope and put it into sniper circulation. wood is not...

    Liked On: 04-11-2019, 07:54 PM

11. 
    Joe_90 liked post by kiwi303 On thread : All things BSA

    122296 This BSA started off standard and in british hand in ww2 Following the war it was acquired by the Israeli's who made the scope and put it into sniper circulation. wood is not...

    Liked On: 18-10-2019, 11:48 AM

12. 
    lee308 liked post by kiwi303 On thread : 2208 and 2206h powder for No.4 303

    I've always had good luck with 40-41 grains of 2208 behind a 180 FMJ. always work up though.

    Liked On: 24-09-2019, 09:39 AM

13. 
    PERRISCICABA liked post by kiwi303 On thread : Gun Porn, show off your new toys

    67481 Since the move down south I've been finding myself bush hunting a fair bit. Recently saw a bargain which I've turned into a T3x 308 bushpig, shown next to my T3 7RM, the Tikka family is...

    Liked On: 20-04-2017, 06:59 PM

14. 
    PERRISCICABA liked post by kiwi303 On thread : help with .308 brass sizing in southland

    has been sent off to 7mmSAUM already but thanks for the offer mate!

    Liked On: 19-04-2017, 10:16 PM

15. 
    Danny liked post by kiwi303 On thread : help with .308 brass sizing in southland

    I don't have a press at all unfortunately mate a Lee loader is just a primitive neck sizing set up, Will see if there's anyone else around these ways keen to help first but thanks for the offer!

    Liked On: 17-04-2017, 01:02 AM

Page 7 of 7 First 1234567

• Jump to page: