Larskramer
Member

267 Likes

Page 7 of 18 First 123456789101112131415161718 Last

• Jump to page:

1. 
   Larskramer liked post by Steera1 On thread : rifle change / load/ no bumps etc

   That looks much better larskramer, glad I could help. I know mine was only a couple of weeks ago and was very frustrating, tried all sorts but then it came to me while driving to work about how mine...

   Liked On: 05-10-2022, 07:14 AM

2. 
   Larskramer liked post by grandpamac On thread : Rem700 adl front trigger sceew

   Greetings, I didn't have a problem with the ADL as such other than the stock did not fit me with the high comb and plastic but plate (it is a .308). The Hogue is much more comfortable as I became...

   Liked On: 04-10-2022, 03:11 PM

3. 
   Larskramer liked post by dannyb On thread : Rem700 adl front trigger sceew

   don't forget to re check your zero :thumbsup:

   Liked On: 04-10-2022, 08:41 AM

4. 
   Larskramer liked post by caberslash On thread : Rem700 adl front trigger sceew

   The ADL has it's upsides, no floorplate to open or magazine to drop out, and the stock is much more robust.

   Liked On: 04-10-2022, 08:33 AM

5. 
   Larskramer liked post by Friwi On thread : Rem700 adl front trigger sceew

   I think he mentionned the small middle screw on an adl plateform ( the one holding the front of the trigger guard)

   Liked On: 03-10-2022, 09:09 PM

6. 
   Larskramer liked post by Friwi On thread : Rem700 adl front trigger sceew

   Just a light tension with a bit of blue loctite and that is how do all of mines. Less chance of creating stress in the bedding and the action.

   Liked On: 03-10-2022, 07:53 PM

7. 
   Larskramer liked post by 6x47 On thread : rifle change / load/ no bumps etc

   A just touching suppressor bush will give you a variable zero each time you refit it. Make sure there is clearance -all- round.

   Liked On: 03-10-2022, 06:54 PM

8. 
   Larskramer liked post by chainsaw On thread : rifle change / load/ no bumps etc

   Yep, been caught with suppressor bush issue - some times touching bbl, recently myself. Bought a REM model 7, came with a DPT suppressor. During load dev found it would throw 1 shot out of 3 wide or...

   Liked On: 03-10-2022, 03:51 PM

9. 
   Larskramer liked post by 199p On thread : rifle change / load/ no bumps etc

   Sounds like you found the problem mate

   Liked On: 03-10-2022, 03:47 PM

10. 
    Larskramer liked post by MB On thread : One up the spout

    I primarily hunt using a single shot rifle, so there is always "one up the spout". The rifle has a cocking hammer, but no safety. I hunt alone in the bush with this setup and only cock the rifle just...

    Liked On: 03-10-2022, 01:09 PM

11. 
    Larskramer liked post by Woody On thread : rifle change / load/ no bumps etc

    Check that the bolt lever has clearance from the stock when closed and firing pin forward as if discharged.

    Liked On: 02-10-2022, 07:14 PM

12. 
    Larskramer liked post by chainsaw On thread : Quick wander off Clements Rd.

    Weather was mild, misty but almost no wind. Crap settled in after I came out of scrub

    Liked On: 30-09-2022, 06:29 PM

13. 
    Larskramer liked post by dannyb On thread : Gun Safe Upgrade

    Probably already aware but garages can be prone to larger temperature fluctuations due to less insulation which can create issues with condensation and rust if not mitagated :thumbsup:

    Liked On: 30-09-2022, 02:50 PM

14. 
    Larskramer liked post by No good names left On thread : Gun Safe Upgrade

    I've passed inspection with the safe in a separate garage, so no problem there. I'd love a discrete in-floor safe, you can't steel what you can't find.

    Liked On: 30-09-2022, 02:50 PM

15. 
    Larskramer liked post by iambatman On thread : Sighted in my first rifle

    The shot off to the left was the second in the group. One and three are touching. I'm fairly confident that shot two is down to shooter error. And I'm awful with the batarang. That's the motivation...

    Liked On: 30-09-2022, 01:44 PM

Page 7 of 18 First 123456789101112131415161718 Last

• Jump to page: