Larskramer
Member

255 Likes

Page 6 of 17 First 1234567891011121314151617 Last

• Jump to page:

1. 
   Larskramer liked post by Friwi On thread : how to tell 9/16x24 vs m15

   9/16-24 is 14.29mm outside diameter and Internal is about 13.2 depending of the manufacturers tolerances. 15x1 is 15 mm outside diameter and about 14 mm internal . Don’t shoot with your 15x1...

   Liked On: 06-10-2022, 07:06 PM

2. 
   Larskramer liked post by Moa Hunter On thread : Thermal monocular - thinking about buying one

   I have seen wording somewhere that states that a firearm may not be discharged during the hours of darkness

   Liked On: 05-10-2022, 09:35 AM

3. 
   Larskramer liked post by 223nut On thread : Thermal monocular - thinking about buying one

   It's not hunting if your just looking.... I hunt with a rifle and look with binoculars

   Liked On: 05-10-2022, 07:39 AM

4. 
   Larskramer liked post by Steera1 On thread : rifle change / load/ no bumps etc

   That looks much better larskramer, glad I could help. I know mine was only a couple of weeks ago and was very frustrating, tried all sorts but then it came to me while driving to work about how mine...

   Liked On: 05-10-2022, 07:14 AM

5. 
   Larskramer liked post by grandpamac On thread : Rem700 adl front trigger sceew

   Greetings, I didn't have a problem with the ADL as such other than the stock did not fit me with the high comb and plastic but plate (it is a .308). The Hogue is much more comfortable as I became...

   Liked On: 04-10-2022, 03:11 PM

6. 
   Larskramer liked post by dannyb On thread : Rem700 adl front trigger sceew

   don't forget to re check your zero :thumbsup:

   Liked On: 04-10-2022, 08:41 AM

7. 
   Larskramer liked post by caberslash On thread : Rem700 adl front trigger sceew

   The ADL has it's upsides, no floorplate to open or magazine to drop out, and the stock is much more robust.

   Liked On: 04-10-2022, 08:33 AM

8. 
   Larskramer liked post by Friwi On thread : Rem700 adl front trigger sceew

   I think he mentionned the small middle screw on an adl plateform ( the one holding the front of the trigger guard)

   Liked On: 03-10-2022, 09:09 PM

9. 
   Larskramer liked post by Friwi On thread : Rem700 adl front trigger sceew

   Just a light tension with a bit of blue loctite and that is how do all of mines. Less chance of creating stress in the bedding and the action.

   Liked On: 03-10-2022, 07:53 PM

10. 
    Larskramer liked post by 6x47 On thread : rifle change / load/ no bumps etc

    A just touching suppressor bush will give you a variable zero each time you refit it. Make sure there is clearance -all- round.

    Liked On: 03-10-2022, 06:54 PM

11. 
    Larskramer liked post by chainsaw On thread : rifle change / load/ no bumps etc

    Yep, been caught with suppressor bush issue - some times touching bbl, recently myself. Bought a REM model 7, came with a DPT suppressor. During load dev found it would throw 1 shot out of 3 wide or...

    Liked On: 03-10-2022, 03:51 PM

12. 
    Larskramer liked post by 199p On thread : rifle change / load/ no bumps etc

    Sounds like you found the problem mate

    Liked On: 03-10-2022, 03:47 PM

13. 
    Larskramer liked post by MB On thread : One up the spout

    I primarily hunt using a single shot rifle, so there is always "one up the spout". The rifle has a cocking hammer, but no safety. I hunt alone in the bush with this setup and only cock the rifle just...

    Liked On: 03-10-2022, 01:09 PM

14. 
    Larskramer liked post by Woody On thread : rifle change / load/ no bumps etc

    Check that the bolt lever has clearance from the stock when closed and firing pin forward as if discharged.

    Liked On: 02-10-2022, 07:14 PM

15. 
    Larskramer liked post by chainsaw On thread : Quick wander off Clements Rd.

    Weather was mild, misty but almost no wind. Crap settled in after I came out of scrub

    Liked On: 30-09-2022, 06:29 PM

Page 6 of 17 First 1234567891011121314151617 Last

• Jump to page: