Marty Henry
Member

5157 Likes

Page 288 of 344 First ... 188238274275276277278279280281282283284285286287288289290291292293294295296297298299300301302338 ... Last

• Jump to page:

1. 
   deer243 liked post by Marty Henry On thread : Pig

   Pork doesn't get better with ageing, three days in a chiller is about max. No chiller break it down and fridge works fine as they go off real quick.

   Liked On: 06-12-2017, 05:23 PM

2. 
   Sarvo liked post by Marty Henry On thread : Pig

   Pork doesn't get better with ageing, three days in a chiller is about max. No chiller break it down and fridge works fine as they go off real quick.

   Liked On: 06-12-2017, 04:58 PM

3. 
   Maca49 liked post by Marty Henry On thread : Bushing The Firing Pin Hole

   Is it a problem? Ive got a zastava, and sako that produce little rings round the primer like that and several others that dont. Its never worried me as i just think the pins too thin. For interest my...

   Liked On: 06-12-2017, 06:07 AM

4. 
   Bernie liked post by Marty Henry On thread : Hardy Tikka Carbon Stock and Barrel Good deal ?

   Lipstick and pigs come to mind here.

   Liked On: 05-12-2017, 06:30 AM

5. 
   Beaker liked post by Marty Henry On thread : Off topic need to build a Recirculating water system for my still ideas and opinions?

   flow through the condenser should have the distillate coming out at the same temp as the water is going in. Over 5 hours to get 2 litres of absolute alcohol from a reflux still you will have boiled...

   Liked On: 02-12-2017, 05:27 PM

6. 
   Tommy liked post by Marty Henry On thread : Off topic need to build a Recirculating water system for my still ideas and opinions?

   flow through the condenser should have the distillate coming out at the same temp as the water is going in. Over 5 hours to get 2 litres of absolute alcohol from a reflux still you will have boiled...

   Liked On: 02-12-2017, 03:11 PM

7. 
   john m liked post by Marty Henry On thread : Remington in a Spot of Bother

   I quite like my rolling block.

   Liked On: 30-11-2017, 09:46 AM

8. 
   WillB liked post by Marty Henry On thread : Pulling and tension

   Ive done it often after using an inertia puller (the lee one) I try not to have to do it to often as its more fun to "push the bullet out of a barrel"

   Liked On: 28-11-2017, 12:33 PM

9. 
   Gibo liked post by Marty Henry On thread : Pulling and tension

   Well this forum is about shooting

   Liked On: 28-11-2017, 08:57 AM

10. 
    Cordite liked post by Marty Henry On thread : Pulling and tension

    Ive done it often after using an inertia puller (the lee one) I try not to have to do it to often as its more fun to "push the bullet out of a barrel"

    Liked On: 27-11-2017, 11:44 PM

11. 
    40mm liked post by Marty Henry On thread : Remington in a Spot of Bother

    I quite like my rolling block.

    Liked On: 27-11-2017, 09:39 PM

12. 
    capey liked post by Marty Henry On thread : Recommendations for cheap, legal, 2-4 gun safe?

    Build one out of 20mm ply, it would be way stronger and cost about the same. Also build it bigger than you think you need. Guns have a way of mysteriously growing in number.

    Liked On: 21-11-2017, 06:37 PM

13. 
    SlimySquirrel liked post by Marty Henry On thread : Nightforce Atacr Problem?

    Some little scrote somewhere has a good piece of glass on a rifle they probably lost too.

    Liked On: 20-11-2017, 03:33 PM

14. 
    Tikka7mm08 liked post by Marty Henry On thread : Nightforce Atacr Problem?

    Some little scrote somewhere has a good piece of glass on a rifle they probably lost too.

    Liked On: 20-11-2017, 10:37 AM

15. 
    Iggy liked post by Marty Henry On thread : People very sick after eating wild pig

    Very unlikely, if it was so heavily loaded with 1080 it would have been well dead. Say the pig was 50 kg (a good sized pig) and you ate 1 kg (a bloody lot of meat in one sitting) you would only...

    Liked On: 19-11-2017, 10:55 PM

Page 288 of 344 First ... 188238274275276277278279280281282283284285286287288289290291292293294295296297298299300301302338 ... Last

• Jump to page: