Micky Duck
Member

38309 Likes

Page 963 of 2554 First ... 4638639139499509519529539549559569579589599609619629639649659669679689699709719729739749759769771013106314631963 ... Last

• Jump to page:

1. 
   Micky Duck liked post by Wingman On thread : Old Single shot rifle

   Thank you for the HRB co info. What does the ICI on the other side stand for? The barrel hasnt been shortened, it is the factory artillary carbine length, the fore wood is from a rifle length ME...

   Liked On: 20-01-2023, 06:43 PM

2. 
   Micky Duck liked post by gundoc On thread : Old Single shot rifle

   HRB Co stands for Henry Rifle Barrel Company that did the conversion to .303 in 1898. AC II stands for Artillery Carbine Mark II. The fore-end is incorrect but is similar to the first pattern .303...

   Liked On: 20-01-2023, 06:42 PM

3. 
   Micky Duck liked post by Puffin On thread : Drop chart help

   I quite agree, and also my style, but we can only go on what the OP has told us and answer his queries accordingly, and that was with a limit of 320m. This limit brings other options into the mix...

   Liked On: 20-01-2023, 06:40 PM

4. 
   Micky Duck liked post by TeRei On thread : CFE223 & 55 grain .223

   748 for the triple deuce. BM2 for 223. My mate loves the 55gr Hornady. Getting superb accuracy from 8t Tikka.

   Liked On: 20-01-2023, 06:34 PM

5. 
   Micky Duck liked post by Gibo On thread : Drop chart help

   Way to blow the poor buggers head up:redbullsmiley:

   Liked On: 20-01-2023, 06:29 PM

6. 
   Micky Duck liked post by Preacher On thread : dpt suppressor cleaning

   I have to disagree here. Short .243 had annihilated first baffle in less than a box. DPT were GCs about it though.

   Liked On: 20-01-2023, 06:24 PM

7. 
   Micky Duck liked post by Makros On thread : dpt suppressor cleaning

   To be honest, I don't bother. I've pulled them apart a few times thinking I better clean it and never found anything that I think would require cleaning. Spraying it with WD40 just seems to be an...

   Liked On: 20-01-2023, 06:23 PM

8. 
   Micky Duck liked post by Trout On thread : Drop chart help

   My 308 with a 18 inch barrel,using Hornady Superformance 150ssts.2.5'' inchs high at a hundy give me 2.5'' low at 276yds.Scope is 2" high.Thursday morning spotted 2 deer at 330 yds.Quick dial up to 4...

   Liked On: 20-01-2023, 06:19 PM

9. 
   Micky Duck liked post by tac a1 On thread : Feeling sick after reading this !

   The dealers check only tells them if the firearms license number is current. Nothing else. No Photo, nothing. The only link is the sellers looking at the photo on the license to make sure that the...

   Liked On: 20-01-2023, 05:21 PM

10. 
    Micky Duck liked post by Happy Jack On thread : Drop chart help

    This is an interesting read as I'm about to go down the almost same route with my short 308 but for now using only factory ammo until I can get dies and supplies sorted which could be 6 months down...

    Liked On: 20-01-2023, 05:15 PM

11. 
    Micky Duck liked post by Tahr On thread : Pet loads for the 7x57

    Thats good. You know don't you that every time you do that it means there are 5 less primers in the world. Just say'n. :)

    Liked On: 20-01-2023, 05:05 PM

12. 
    Micky Duck liked post by southernman On thread : Pet loads for the 7x57

    I ran a crony on federal blue box, of 175 round nose, in my M70 7x57 and got 2250fps,

    Liked On: 20-01-2023, 05:04 PM

13. 
    Micky Duck liked post by Moa Hunter On thread : Pet loads for the 7x57

    Depends how far back in time you go I would guess. My uncle ran a BSA 7mil for Tahr culling in the 60's and said that the best ammo was 'Imperial' out of Canada. Think it was 140 grn 'Cone point'....

    Liked On: 20-01-2023, 05:03 PM

14. 
    Micky Duck liked post by Seventenths On thread : CFE223 & 55 grain .223

    I played around with a few loads in my T3 .223 with 55 gr projectiles but wasn’t overly happy. I had better results accuracy wise with AR2206H I never ran the loads through a chronograph as I was...

    Liked On: 20-01-2023, 05:02 PM

15. 
    Micky Duck liked post by Tahr On thread : CFE223 & 55 grain .223

    I got the cfe223 for my 7-08 which has gone as part of the great thinning. Great powder in 7-08. Yes, I would swap and would be generous with the exchange.. Ive got about 4kg of cfe223.

    Liked On: 20-01-2023, 05:02 PM

Page 963 of 2554 First ... 4638639139499509519529539549559569579589599609619629639649659669679689699709719729739749759769771013106314631963 ... Last

• Jump to page: